Kenwood FC-757 Скачать руководство пользователя страница 26

Страница: 26 / 40

If the s w i t c h is pressed (

jm-

), the t r a n s i t i o n

t i m e w i l l be measured in milliseconds.

If left open ( • ) . it w i l l be measured in

microseconds. The display unit indication

L E D , k H z / ^ s

(3)

or M H z / m s ® , w i l l become

a c t i v e according to the selection.

(6) Select a desired resolution value w i t h G A T E

s w i t c h © .

(7) The time interval measurement value w i l l be

output to the D i s p l a y . G A T E L E D ® blinks

during the measurement. The output measure-

ment d a t a on the D i s p l a y w i l l be updated a t

the moment when one measurement interval

is over.

The G A T E L E D blinking m a y not be confirmed

because it gets too f a s t due to high-frequency

input s i g n a l .

Note : The measurement m a y be delayed or

the output value display m a y be

unstable. In this case, refer to section

5 - 6 ' D i s p l a y D e s c r i p t i o n ' .

(8) If H O L D s w i t c h © is turned on during

measurement, the current measurement value

on the D i s p l a y is held a s it i s .

If it is turned o f f , a new measurement cycle

w i l l be s t a r t e d . However, the measurement

value currently being displayed w i l l remain

unchanged u n t i l the new measurement cycle is

complete. T h a t i s , the display value being

held by the H O L D s w i t c h is updated by the

output value f r o m the new measurement

operation.

(9) If R E S E T s w i t c h © is pressed during the

time interval measurement, the measurement

value on the D i s p l a y w i l l be reset to

' 0 ' .

If pressed a g a i n , a new measurement cycle

w i l l be s t a r t e d . However, the measurement

value w i l l remain

' 0 '

until the new cycle is

complete.

(10)

T i m e interval measurement between t w o single-

shot pulses. .

The time t r a n s i t i o n f r o m one single shot to

another single shot can be measured.

Set G A T E s w i t c h © to the 1/0.01$ position.

Note t h a t the s w i t c h should be a l w a y s set

to t h i s position in the single-shot t i m e

Содержание FC-757









































Результаты поиска

Содержание FC-757

Отзывы:

Kenwood FC-757, Инструкция по эксплуатации, Страница: 26 / 40

Результаты поиска

Содержание FC-757

Отзывы: