Kenwood FC-757 Скачать руководство пользователя страница 10

Страница: 10 / 40

The display consists of eight-digit L E D s

indicating a l l the current measurement v a l u e .

• The O V E R F L O W L E D is provided to n o t i f y

the user t h a t an overflow has occurred.

c k

The C H A N N E L B input juck is provided to

allow object s i g n a l s to enter the counter.

T h i s juck is used f o r frequency r a t i o measure-

ment and t i m e interval measurement.

The C H A N N E L B input juck is a B N C connector

terminated w i t h a resistor of 1.2megaohm.

The m a x i m u m input voltage is 125Vrms.

The A T T (enuation) x 10 s w i t c h is provided to

enable the internal A T T e n u a t o r c i r c u i t

operation.

If t h i s s w i t c h is pressed ( x 10), the input

signal to channel B is attenuated into 1/10 and

then reaches the counter.

If t h i s s w i t c h is pressed again ( x 1 ) , the input

signal to channel B reaches the counter w i t h o u t

attenuatjon.

Note t h a t t h i s s w i t c h can w o r k together w i t h

channel B only but does not a f f e c t channel A .

The - S L O P E s w i t c h is provided to permit the

user to select positive-going edge or negative-

going edge of the C H A N N E L B signal f o r s y n -

chronization.

If t h i s s w i t c h is pressed

( m ) ,

negative-going

edge w i l l be selected f o r s y n c h r o n i z a t i o n .

If t h i s s w i t c h is pressed again ( J U L ) , positive-

going edge w i l l be selected f o r s y n c h r o n i z a t i o n .

The C H A N N E L A input juck is provided to a l l o w

signals to be input to the counter f o r frequency

measurement and period measurement.

In the frequency r a t i o measurement mode, the

r a t i o between the C H A N N E L B inputs and the

C H A N N E L A inputs is measured.

In the time interval measurement mode, the

difference in t i m e between the C H A N N E L B

inputs and the C H A N N E L A inputs is measured.

The C H A N N E L A input juck is a B N C connector

Содержание FC-757









































Результаты поиска

Содержание FC-757

Отзывы:

Kenwood FC-757, Инструкция по эксплуатации, Страница: 10 / 40

Результаты поиска

Содержание FC-757

Отзывы: