manualshive.com logo in svg

Kenwood FC-757, Инструкция по эксплуатации, Страница: 14 / 40

Поделиться
Скачать
Kenwood FC-757 Скачать руководство пользователя страница 14

c.  R A T I O  A / B (frequency  r a t i o ) mode 

The  R A T I O  A / B mode is an operational mode 

in which  t h i s product measures both  s i g n a l s 

* on channels A and  B , and then compares the 

C H A N N E L B  s i g n a l s  w i t h those on  C H A N N E L 

A  ( A / B )  f o r  r a t i o  c a l c u l a t i o n . 

The  d i s p l a y resolution can be selected  w i t h 

G A T E  s w i t c h  © . * 

d.  T l / A  - * B  ( t i m e  i n t e r v a l ) mode 

The  T l / A -> B mode is an operational mode 

in  w h i c h  t h i s counter product measures the 

t i m e interval between a selected edge of the 

C H A N N E L A signal and a selected edge of 

the  C H A N N E L B  s i g n a l . 

The edge can be selected  f r o m positive-going 

and negative-going edges of each signal  w i t h 

- S L O P E switches © and  @ . The measurement 

d a t a is displayed in  ^ s or ms selected by 

display unit select  s w i t c h  © .  T h a t display 

unit is indicated by either measurement unit 

display  L E D © or  ® . The display resolution 

can be selected  w i t h  G A T E  s w i t c h  ® . 

e. '  T O T A L / A (event input  t o t a l count) mode 

The  T O T A L / A mode is an operational mode 

in which  t h i s product measures the number of 

channel A input cycles and then outputs each 

count value to the display continuously. 

T h i s cycle count and display operations can 

be  e x t e r n a l l y controlled  w i t h the gate signal 

input to the  T O T A L I Z E  S T A R T / S T O P input 

juck on the rear panel or  H O L D  s w i t c h © on 

the  f r o n t panel. 

f.  C H E C K / 1 0 M H z mode 

The  C H E C K / 1 0 M H z mode is an operational 

mode in which  t h i s universal counter checks 

internal functions. If  t h i s self-check mode is 

selected, the frequency of the internal  t i m e 

base timer  ( 1 0 M H z )  w i l l be displayed by the 

8-digit 7-segment  L E D s . 

©  G A T E  S w i t c h / G A T E  L E D 

The  G A T E  s w i t c h is provided to select a 

desired display resolution value  f o r the meas-

urement modes  s t a r t e d by  F U N C  s w i t c h  © • 

T h i s does not apply to the event  t o t a l count 

14 

Содержание FC-757









































Отзывы:

Нет отзывов