Kenwood FC-757 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 40

Kenwood FC-757 Скачать руководство пользователя страница 13

• T h i s s w i t c h is helpless in the frequency r a t i o

measurement mode and event t o t a l count meas-

urement mode,

® F U N C S w i t c h / M o d e display L E D s

The F U N C s w i t c h is provided to select the

desired operational mode f r o m the a v a i l a b l e

modes.

The mode display L E D s are provided to indicate

the measurement mode selected by t h i s s w i t c h .

The f o l l o w i n g operational modes can be selected

w i t h t h i s s w i t c h ,

a . F R E Q / A (frequency) mode

The F R E Q / A mode is an operational mode in

which t h i s counter measures the frequencies of

input s i g n a l s to channel A and outputs them

to the display section. They are displayed in

either kHz or MegaHerz ( M H z ) . The display

unit can be selected w i t h display unit select

s w i t c h @ and indicated by either display unit

indicator L E D ® or (D. The display resolution

can be selected w i t h G A T E s w i t c h © .

The measurement frequency ranges in each

display range are a s f o l l o w s :

kHz range :

5Hz to 10MHz

Measurement s e n s i t i v i t y :

5Hz to 5 M H z : 20mV r m s

M H z range :

1MHz to 175MHz

Measurement s e n s i t i v i t y :

5 M H to 125MHz : 50mV r m s

125MHz to 150MHz : 100mV r m s

150MHz to 175MHz : 150mV r m s

The proper range should be used according to

input signal frequencies w i t h each range char-

a c t e r i s t i c s f u l l y in mind,

b. P E R / A (Period) mode

The P E R / A mode is an operational mode in

which t h i s product measures the period

of input s i g n a l s to channel A and then

outputs them to the display section. They

are displayed in the unit selected by display

unit select s w i t c h @ . T h a t display unit is

indicated by either display unit indicator L E D

(3)

or @ . The display resolution can be

selected w i t h G A T E s w i t c h © .

13

«
...
11
12
13
14
15
...
»

Содержание FC-757









































Отзывы:

Нет отзывов