Kenwood FC-757 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 40

Kenwood FC-757 Скачать руководство пользователя страница 22

(1) Input a target signal (to be measured) to the

C H A N N E L A input juck.

(2) Select the P E R / A (period) mode w i t h F U N C

s w i t c h @ .

(3) Select a desired measurement unit w i t h display

unit select s w i t c h @ .

If the s w i t c h is pressed ( J " - ) , measurement

output w i l l be displayed in M H z / m s .

If pressed again ( . • _ ) , it w i l l be displayed in

kHz/j«s. In either case, the associated L E D

( k H z / ^ s L E D ® or M H z / m s L E D ® ) w i l l

become a c t i v e .

If the k H z / ^ s L E D turns on, input signals

are measured in microseconds.

If the M H z / m s L E D turns on, input signals

are measured in milliseconds.

(4) Select a desired display resolution value w i t h

G A T E s w i t c h © . T h i s G A T E s w i t c h is used

to specify the number of cycles per period

measurement. A s already explained, the f i n a l

cycle time output is the average of a l l the

cycle t i m e s . The display resolution L E D s

( f r o m the left) indicates 1, 10, 100 and 1000.

The average cycle t i m e of a l l the period

measured is output to D i s p l a y © .

G A T E L E D (2) blinks during the period

measurement.

The measurement value on the display w i l l

be updated a t the moment when one cycle

measurement is complete (when the G A T E

L E D turns o f f ) . The G A T E L E D blinking

may not be confirmed w i t h ease because it

gets too f a s t due to high-frequency signal

measurement.

Note : The measurement m a y be delayed or

the output value display m a y be

unstable. In t h i s case, refer to section

5 - 6 ' D i s p l a y D e s c r i p t i o n ' .

(5) If H O L D s w i t c h © is turned on during period

measurement, the current measurement value

on the D i s p l a y is held as it i s . If it is

turned off, a new measurement cycle w i l l be

s t a r t e d . However, the measurement value

currently being displayed w i l l remain unchanged

until the new measurement cycle is complete.

T h a t i s , the display value being held by the

22

«
...
20
21
22
23
24
...
»

Содержание FC-757









































Отзывы:

Нет отзывов