background image

Introduction and summary

Thank you for your decision to buy a KENTIX monitoring solution based on the KENTIX MultiSensor 
technology.

Features

The Kentix MultiSensor-LAN is an All-in-One system unit with many integrated sensors.
The MultiSensor-LAN can be a stand-alone device or operated in conjunction with a Kentix AlarmManager. 
By the use with an AlarmManager provides you a more extensive functionality.
The MultiSensor-LAN is installed in server room or rack. It controls and forwards all alarm and fault 
messages to the responsible persons.
The configuration is done with the integrated web server, comfortable with a web browser. 
For the connection and installation of the devices you can choose from two options:

Plug and Play 

installation with plug technology - without wiring and jamming. Voltage supply by 

„Power over Ethernet“ (PoE).

Fixed installation

 with conventional installation cables.

Applications

• Industry and Trade
• Banks
• Authorities and hospitals
• Telecommunications
• Law firms and medical practices
• Energy and water utility

Safety note

The installation of the MultiSensors must be run by an competent person.

In a power failure, the settings are not lost. Energized relays drop out and go back when the power returns in 
the unswitched output state.
To bridge longer downtime, use a suitable UPS system.

Installation

To ensure the security and integrity of the operator, and the correct operation of the KENTIX MultiSensor-
LAN, the execution of the installation only has to be done by an expert. There must also the relevant 
requirements are met.

Environment

The installation must be such that the KENTIX MultiSensor-LAN and all associated cables are not affected 
by, environmental conditions: 

dust, humidity, excessive heat, direct sunlight, heat sources, devices 

that build strong electromagnetic fields, liquids or corrosive chemicals.

See the technical data sheet for more technical data and environment conditions.

  

Protection

During the installation of the alarm manager, certain degrees of protection must be guaranteed. Observe the 

relevant regulations for installation in certain environments such as industrial or residential and commercial 

buildings.

Page 3                                          

!

(09-2012, subject to change)

!

www.kentix.de

Содержание MultiSensor-LAN
















Отзывы: