Keltech CNA-36 Скачать руководство пользователя страница 4

4

CNA-Series Tankless Heater

 Installation

7/13/2015 

Keltech • 

215-1814 Rev. C; ECN 150010

Storage Instructions

NOTICE! Keep Keltech Electric Tankless Water Heaters stored in original packaging until installation.  

Recommended storage criteria: 

Store Keltech Electric Tankless Water Heaters where temperatures exceed 35ºF (2º C) at all times .
Indoor storage is recommended .
Minimize excessive on-site transport to reduce risk of shock and impact damage . 

Alternate storage: 

If in the original crate, Keltech Electric Tankless Water Heaters will withstand outside storage for approximately 1 
month in most climates . Crate may not be capable of protecting the heater if left outside longer than this time frame .
If the Keltech Electric Tankless Water Heater is stored in an outdoor environment, care should be taken to protect the 
heaters from:

•  Rain or other falling precipitation via tarp or other waterproof media .
•  Runoff and accumulation of groundwater from any source that may exceed 1 inch . 

NOTICE!  For heaters with ENHT freeze protection option: If the heater is stored where the temperature 

could fall below 45°F(7°C), the heater must be powered immediately after hydro testing to insure 
internal freeze protection components are activated. Once the heater is installed and the on-site 
plumbing has been hydro tested, the power supply must remain constant until the risk of freeze is 
eliminated. If this is not possible, do not allow the heater to remain full of water.  The heater must 
be drained.  Freezing of the heater can cause serious damage.  Follow notes in Start Up Check List 
section following an electrical lockout/tagout procedure.

Packaging

Crates are constructed from 3/4" OSB . 
Crate dimensions approx: 82" x 48" x 24" (2083mm x 1219mm x 610mm)
Crates should not be stacked more than 2 high .
All crates must be stacked evenly and horizontally .
Safety issues related to packaging:

•  Product should be transported with the care associated to packages labeled “FRAGILE” even if packaging is not 

marked accordingly .

•  Standard safety procedures for forklift transport and large items less than 1000lbs should be followed at all times . 
•  When stored, crate must be supported in entirety of its length and width .

Содержание CNA-36





















Отзывы: