Kellfri 35-HKK Скачать руководство пользователя страница 9

Страница: 9 / 36

Table of contents

MACHINERY/EQUIPMENT CONNECTED TO HYDRAULICS

Be careful when you connect your machine or equipment to a hydraulic hose.

•

Warning for high pressure, risk of penetration injury.

•

Before repairs or maintenance are carried out, the system must be relieved of any

remaining pressure.

•

Switch off the tractor and move the hydraulic levers back and forth to release any

pressure that may still be in the oil hoses and pipes before starting any work on them

or the hydraulic cylinders.

•

Clean the filter in the suction pipe after 10 hours’ work.

•

Immediately replace hydraulic hoses if cracks or wear are detected.

•

Do not adjust the valve settings. Incorrect adjustment can result in damage to the machine
and/or injury.

•

The hydraulic system must only be operated using hydraulic oil intended for the purpose.

Check the oil level before you start the machine!

•

When commissioning a new machine, it is recommended that the hydraulic oil is changed

after the first 10 hours of operation, in order to remove any dirt or metal chips which

may have got into the hydraulic system.

NOTE: The oil becomes hot when it flows through the hydraulic system. Check the oil temperature at regular

intervals in order to avoid overheating. Stop the machine if the oil becomes overheated and allow the oil

to cool down.

ENVIRONMENT

DANGER!

Pressurised oil and fuel leaks can penetrate skin and cause serious injuries. Do not use your
hands to locate leaks. Use a piece of paper or cardboard to look for leaks.

•

Disposal of oil and other waste

•

Improper disposal of oil or other waste may be hazardous to

the environment.

•

When oil is emptied from the machine, it must be poured into

a leak-proof container suitable for oil. It is not permissible to store

oil in a container used for food or drink, in order to avoid the oil

being consumed by mistake and causing serious injury.

•

It is prohibited to spill oil on the ground, or pour it into a drain

or anywhere leading to a water source.

•

Discarded oil, fuel, coolant, brake fluid, filters and batteries must

not be thrown away or emptied in just any manner. Contact your

local authority for further information.

Содержание 35-HKK





































Результаты поиска

Содержание 35-HKK

Отзывы:

Похожие инструкции для 35-HKK

Бренды по названию

Популярные бренды

Kellfri 35-HKK, Руководство по эксплуатации

Результаты поиска

Содержание 35-HKK

Отзывы:

Похожие инструкции для 35-HKK

Бренды по названию

Популярные бренды