Kellfri 35-HKK Скачать руководство пользователя страница 16

Страница: 16 / 36

Table of contents

HYDRAULIC HOSES

•

Inspect all hydraulic hoses and couplings daily to ensure that they are in good condition.

•

Pay particular attention to any chafed outer casing.

•

Any damage or leaks must be rectified immediately.

•

Hoses with a damaged metal braid should be replaced.

•

If a coupling is leaking, it must be replaced.

The hose is weakened when installed in twisted

position. In addition, pressure pulses in a twisted hose

tend to wear out threads and loosen connections.

Important!

To avoid twisting when replacing the hose, use two

wrenches to loosen and tighten.

Medium hose,

PRESSURE 1/2"

Marked

RED

Connect the pressure hose is

to the tractor’s hydraulic outlet.

Thicker hose,

RETURN 3/4"

Marked

BLUE

The return hose must be

connected to a free return

on the tractor.

Max. back pressure

return 10 bar.

If the hoses are fitted incorrectly, the gasket in the motor is pushed out, resulting in leakage.

The motor cannot be used until the gasket has been replaced. Pressure in the leakage line must not

exceed pressure in the return hose.

WARNING!

Narrower hose,

LEAKAGE LINE

Marked

DARK BLUE

Connect directly to tank.

Max. 0 bar.

Warning! Must never be

connected to the return!

Warning! It is forbidden

to plug the leakage line!

1/2” quick coupling

3/8" external straight

Banjo 1/4" x 14 mm

1/2” quick coupling

DRAIN

0 bar

PRESSURE

LÄCK

0 bar

TRYCK

TANK

RETURN

RÜCKLAUF

LECK

0 bar

DRUCK

Содержание 35-HKK





































Результаты поиска

Содержание 35-HKK

Отзывы:

Похожие инструкции для 35-HKK

Бренды по названию

Популярные бренды

Kellfri 35-HKK, Руководство по эксплуатации

Результаты поиска

Содержание 35-HKK

Отзывы:

Похожие инструкции для 35-HKK

Бренды по названию

Популярные бренды