Kellfri 35-HKK Скачать руководство пользователя страница 5

Страница: 5 / 36

Table of contents

SURROUNDINGS

Check that the work area is free from bystanders and objects before hitching or using the

equipment. Otherwise, there is a risk of serious injury. Be extra careful if there are children in

the vicinity of the area where the equipment or product is used or stored. Check that there

are no low-hanging electrical cables within the work area. Exercise caution when working

on slopes and close to ditches.

Always work alone with equipment or products that are made for working alone. Never

leave rubbish in the work area, and keep work surfaces clean. Always respect the equipment’s

risk zone.

BEFORE USE

Carefully read the safety instructions and the operating manual. Make sure that you

understand the safety instructions, the instruction manual and warning decals. Use common

sense and suitable personal protective equipment when using the product. Always check the

performance of the machine combination to be used. It is important that these are compatible

and work satisfactorily together. This is to ensure that the equipment or product works

as expected, and to guarantee the safety of yourself and others. Carry out a visual inspection of

the equipment or product before use. Repair or replace damaged or worn parts immediately

to reduce the risk of injury. Grease moving parts and check that all nuts and bolts are

tightened. Repair if necessary. Learn and remember the correct working method. Beginners

must work slowly until they have learned how the machine or product works.

Users/customers are responsible for ensuring users can handle the situation. If a user

feels that the machine is dangerous to use, they should not use it until they have received
thorough training.

WARNING!

Never use equipment or products with defective safety components.

Children must not be left unsupervised in the area!

Warning!

Important! Before using the Strimmer, top up with grease.

(

See page 15.)

All lubrication points are greased after every 30 hours of use.

NOTE: Slowly and carefully pump in grease to prevent damage to the bearing seals.

Be extra careful when using a high-pressure grease gun.

Содержание 35-HKK





































Результаты поиска

Содержание 35-HKK

Отзывы:

Похожие инструкции для 35-HKK

Бренды по названию

Популярные бренды

Kellfri 35-HKK, Руководство по эксплуатации

Результаты поиска

Содержание 35-HKK

Отзывы:

Похожие инструкции для 35-HKK

Бренды по названию

Популярные бренды