Safety precautions
The following safety precautions should be observed before using this product and any
associated instrumentation. Although some instruments and accessories would normally
be used with nonhazardous voltages, there are situations where hazardous conditions
may be present.
This product is intended for use by qualified personnel who recognize shock hazards
and are familiar with the safety precautions required to avoid possible injury. Read and
follow all installation, operation, and maintenance information carefully before using the
product. Refer to the user documentation for complete product specifications.
If the product is used in a manner not specified, the protection provided by the product
warranty may be impaired.
The types of product users are:
Responsible body
is the individual or group responsible for the use and
maintenance of equipment, for ensuring that the equipment is operated within
its specifications and operating limits, and for ensuring that operators are
adequately trained.
Operators
use the product for its intended function. They must be trained in
electrical safety procedures and proper use of the instrument. They must be
protected from electric shock and contact with hazardous live circuits.
Maintenance personnel
perform routine procedures on the product to keep it
operating properly, for example, setting the line voltage or replacing
consumable materials. Maintenance procedures are described in the user
documentation. The procedures explicitly state if the operator may perform
them. Otherwise, they should be performed only by service personnel.
Service personnel
are trained to work on live circuits, perform safe
installations, and repair products. Only properly trained service personnel may
perform installation and service procedures.
Keithley Instruments products are designed for use with electrical signals that are
measurement, control, and data I/O connections, with low transient overvoltages, and
must not be directly connected to mains voltage or to voltage sources with high
transient overvoltages. Measurement Category II (as referenced in IEC 60664)
connections require protection for high transient overvoltages often associated with
local AC mains connections. Certain Keithley measuring instruments may be connected
to mains. These instruments will be marked as category II or higher.
Unless explicitly allowed in the specifications, operating manual, and instrument labels,
do not connect any instrument to mains.
Exercise extreme caution when a shock hazard is present. Lethal voltage may be present
on cable connector jacks or test fixtures. The American National Standards Institute
(ANSI) states that a shock hazard exists when voltage levels greater than 30 V RMS,
42.4 V peak, or 60 VDC are present. A good safety practice is to expect that hazardous
voltage is present in any unknown circuit before measuring.
Operators of this product must be protected from electric shock at all times. The
responsible body must ensure that operators are prevented access and/or insulated from
every connection point. In some cases, connections must be exposed to potential
human contact. Product operators in these circumstances must be trained to protect
themselves from the risk of electric shock. If the circuit is capable of operating at or
above 1000 V, no conductive part of the circuit may be exposed.
Содержание 8010
