KDF Neo Super Cascom Скачать руководство пользователя

Страница: 23 / 25

- 21 -

Trouble Shootings

■

When you find your unit is in trouble, we recommend you to check the
problem with those guides listed below before you send out for repair.
If the guide below does not solve the problem, contact the nearest dealer
or manufacturer.

Troubles

Causes

Recommendations for solution

Display does not light up. Is the unit unplugged ?

Plug in the unit

Is the power switch off ?

Turn the power switch on

Power goes off despite of

Contact dealer or manufacturer

power being switched on.

Muffle is not heating up

Is muffle heat below

Power flow to heater in low heat

or slow in heat up

212

100

level is restricted to sustain

(

℃)



muffle life. This is not abnormal.

Is start temp. programmed

Check the programmed start

low ?

temp to revise or to adjust.

P12

→

The machine makes a

Is muffle in heat rise ?

When the small lamp on the

buzzing sound

bottom right of the 4 digit
display is illuminated, it may
sound buzzing.
This is not abnormal.

The pocket pager does

The pager has not received

Refer to P17 and follow the

not work

data from the unit properly.

instruction for recheck.

The cycle counter will not Is the bar code on the crucible Use of a new ceramic crucible
read ceramic crucible

contaminated or chipped ?

is recommendable.

data

is displayed

Abnormal vacuum level.

Is the vacuum pump fuse





Vacuum pump is unable to

blown ? While you press the

reach a proper level.

vacuum pump fuse lightly with
a driver, turn the fuse approx.
60

counter clockwise to draw

out the fuse for replacement.
The rating of the fuse in 125V,
M10A is recommended.

is displayed

Vacuum pump may be

This enables you to cast but



after finish of casting

deteriorated or a proper

you may have a miscasting.

operation

vacuum level was not

Contact to manufacturer is

obtained by vacuum leak.

recommendable.

are

Crucible cycle was not

Place the crucible in the cycle

 

displayed.

checked.

counter to make sure if the
crucible is good for use or not.

P13

→

Affection to receivers

When the unit is in operation,

Keep away the receivers such

such as radios by the

you may have occasions when as radios from the unit.

noise.

your radio receiver in the
vicinity will be attacked by
the noises generated from
the unit.

Содержание Neo Super Cascom


























Результаты поиска

Содержание Neo Super Cascom

Отзывы:

Похожие инструкции для Neo Super Cascom

Бренды по названию

Популярные бренды

KDF Neo Super Cascom, Инструкция по эксплуатации

Результаты поиска

Содержание Neo Super Cascom

Отзывы:

Похожие инструкции для Neo Super Cascom

Бренды по названию

Популярные бренды