background image

02

1 SAFETY PRECAUTIONS

The precautions listed here are divided into the following types.They are quite important, so be sure to follow them carefully. 

Meanings of DANGER, WARNING, CAUTION and NOTE symbols.

i

INFORMATION

●  Read these instructions carefully before installation. Keep this manual in a handy for future reference.
●  Improper installation of equipment or accessories may result in electric shock, short-circuit, leakage, fire or other 

damage to the equipment. Be sure to only use accessories made by the supplier, which are specifically designed for 

the equipment and make sure to get installation done by a professional.

●  All the activities described in this manual must be carried out by a licensed technician. Be sure to wear adequate 

personal protection equipment such as gloves and safety glasses while installing the unit or carrying out maintenance 

activities.

●  Contact your dealer for any furthur assistance.

Caution:Risk of fire/ 

flammable materials 

for IEC/EN 60335-2-40 

except IEC 60335-2-40

2018

Caution:Risk of fire/ 

flammable materials 

for IEC 60335-2-40 : 2018 only

WARNING

Servicing shall only be performed as recommended by the equipment manufacturer. Maintenance and repair requiring 

the assistance of other skilled personnel shall be carried out under the supervision of the person competent in the use of 

flammable refrigerants.

 DANGER

 WARNING

 CAUTION

 NOTE

Indicates an imminently hazardous situation which if not avoided, will result in serious injury.

Indicates a potentially hazardous situation which if not avoided, could result in serious injury.

Indicates a potentially hazardous situation which if not avoided, may result in minor or moderate injury.
It is also used to alert against unsafe practices.

Indicates situations that could only result in accidental equipment or property damage.

Explanation of symbols displayed on the unit

WARNING

This symbol shows that this appliance used a flammable refrigerant. If the refrigerant is 

leaked and exposed to an external ignition source, there is a risk of fire.

CAUTION

This symbol shows that the operation manual should be read carefully.

CAUTION

This symbol shows that a service personnel should be handling this equipment with 

reference to the installation manual.

CAUTION

This symbol shows that information is available such as the operating manual or installation 

manual.

Содержание KSWP-70 DR8

































Отзывы: