8
depending on conditions. In most cases a power washer
will be sufficient if the unit and algae are still wet. Also,
make sure the lens of the light fixtures is clean to ensure the
brightest light possible.
FIXTURE REPLACEMENT: The LED light fixtures
are sealed and do not require any maintenance other than
cleaning. If a fixture fails to operate it can be removed and
the sealing cap installed onto the waterproof connector of
the power cord. This will allow you to continue to operate
your light kit with two fixtures while a replacement fixture
is procured. Only perform this removal/replacement with
all equipment disconnected from the power source.
Any required repairs need to be performed by Kasco
Marine. Any alterations or changes made to Kasco units
by an unauthorized source will void the warranty. This
includes tampering with the unit, power cord, and/or
control box.
Please contact Kasco Marine, Inc. at 715-262-4488 or
[email protected].
Warranty Policy
Warranty period:
RGB3C5 and RGB6C5 = 2 year
Limited Warranty: Kasco® Marine, Inc. warrants
this Light Kit to be free from defects in material or
workmanship un- der normal use and service. The
Kasco Marine, Inc. obligation under this warranty is
limited to replacing or repairing free of charge any
defective part within the warranty period from the date
of shipment. Customer shall pay shipping charges for
returning the unit to Kasco.
THIS WARRANTY IS IN LIEU OF ANY OTHER
WARRANTIES, EXPRESSED OR IMPLIED, AND
ANY OTHER OBLIGATION OR LIABILITY
WHATEVER ON THE PART OF KASCO MARINE,
INC. AND IN NO EVENT, SHALL KASCO
MARINE, INC. BE LIABLE FOR ANY SPECIAL
OR CONSEQUENTIAL DAMAG- ES.
Warranty is void if:
The Light Kit is not maintained properly according to
the Maintenance Recommendations supplied in this
Owner’s Manual.
The lights, control box, or power cord are altered in
audio source to the RGB controller and your stereo
amplifier simultaneously if desired.
Maintenance Recommendations
•
Under No Circumstances should anyone enter the
water while a fountain is operating.
•
Please keep the original box for maintenance shipping.
The following maintenance procedures can be utilized to
ensure many years of quality performance from your Kasco
Fountain and Light Kit and reduce the need for more costly
repair work.
PROPER INSTALLATION: Proper installation of Kasco
equipment will include a power source with ground fault
protection. For Fountain models, Kasco provided control
panels included with the unit have built-in ground fault
protection. Ground fault interrupters are a safety feature
that
can also alert you to electrical leaks in the equipment. If
you have repeat, consistent trips of the ground fault device,
the equipment should be disconnected and removed from
the water. The power cord should be inspected for dam-
age and you should contact your distributor, or call Kasco
Marine at 715-262-4488 for further instructions or email
Kasco at [email protected].
OBSERVATION: Operating equipment should be observed
on a regular basis (daily, if possible) for any reduction
or variation in performance. If a change in performance
is observed, the equipment should be disconnected from
power and inspected.
WINTER STORAGE: In regions where there is significant
freezing in the wintertime, the fountain and light kit
should be removed from the water to protect them from
the expansion pressure of the ice. In many areas, fountains
will keep some amount of ice open through the winter.
However, when the water is thrust into the air, it is exposed
to the colder air temperatures longer and can actually make
ice thicker on the pond/lake. Storage over winter is best in a
location that is out of the sun and cool, but above 32° F.
CLEANING: Fountains and light kits should be removed
from the water at least once per year (at the end of the
season in cold climates) to clean the exterior of the system,
especially the stainless steel motor housing (can) and light
fixtures. The motor housing and light fixture surfaces
dissipate heat into the water and any algae, calcium, etc.
build-up will become an insulator that blocks heat transfer.
In warmer regions, it is recommended that the motor
is removed and cleaned at least two to three times per year
