background image

WARRANTY, WARRANTY CLAIM, & RETURN POLICY 

 

2 Year Limited Warranty

: Kasco

® 

Marine, Inc. warrants this De-Icer to be free from defects in material or 

workmanship (except for the ropes, power cord, ropes, and propeller) under normal use and service.  The 
Kasco Marine, Inc. obligation under this warranty is limited to replacing or repairing free of charge any 
defective part within two (2) years from the date of shipment.  

Customer shall pay shipping charges for 

returning the unit to Kasco or an Authorized Repair Center. 

 

 

THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESSED OR   IMPLIED, 

 

AND ANY OTHER OBLIGATION OR LIABILITY WHATEVER ON THE PART OF KASCO 

 

MARINE, INC. AND IN NO EVENT SHALL KASCO MARINE, INC. BE LIABLE FOR ANY 

 

SPECIAL OR CONSEQUENTIAL DAMAGES. 

 

Warranty is void if: 

 

• 

The De-Icer is not maintained properly according to the Maintenance Recommendations supplied in this 
Owners Manual. 

 

• 

The De-Icer is returned for repair without the power cord or if the unit or power cord are altered in any 
way from original shipment.  

Cuts in the power cord are not covered under warranty.

 

 

• 

The De-Icer is damaged by unauthorized tampering. 

 

• 

The Sacrificial Zinc Anode around the propeller shaft shows significant deterioration.  (The Anode must be 
inspected periodically and replaced if necessary.) 

 

Note:  There are certain conditions under which no circulator can prevent ice damage such as ice that moves 
due to wind or current, extremely cold weather where ice forms all the way to the bottom and in some cases 
where the bottom water temperature is the same as ice (very shallow water).  Effective operation can be some-
what reduced when flow is restricted by too little bottom clearance.

 

 

Warranty Claim Procedure: 

 

Check the ten-digit serial number printed either on the black cover of the motor or on the blue nameplate and 
determine the year of manufacture according to the serial number scheme below: 

 

Sample Serial # 

6001  D 2  1725 

 

• 

The first two digits represent the reverse of the last two digits of the year of manufacture.   

      Example: 60 = 2006 model year. 

 

• 

The third and fourth digits represent the week of the year.  (Ex. “01” for 1st week in Jan.) 

 

• 

The fifth digit represent the model.  (Ex. “D” for 2400D) 

 

• 

The sixth digit represents the horsepower of the unit in fourths: 2 = 2/4 = 1/2HP, 3 = 3/4HP, 4 = 1HP. 

 

• 

The remaining four digits are sequential. 

 

The best method for establishing warranty period is registering your De-Icer online at the below address and/or 
the original receipt.  If the customer has registered the De-Icer online at:  
www.de-icer.com/solutions_warranty_registration.htm ,  
Kasco Marine will have a record of the purchase and will be able to determine whether or not the unit still car-
ies warranty coverage. 

 

Содержание 2400D























Отзывы: