Kärcher SE 4002, Оригинальное руководство пользователя

Страница: 12 / 138

– 7
Illustration
 Install the fresh water reservoir . Insert the bot-
tom part first and then press toward the top on the
motor compartment to check if it is locked in.
Illustration
 Attach the suction hose and the spray hose to the
connectors on the appliance.
Note
: Press the suction hose tightly into the connector
to lock it into place.
Illustration
 Connect the spray/suction pipes and attach to the
handle. Center the locking lever when attaching it,
turn clockwise to lock.
 Attach the floor nozzle to the spray/suction pipes
and secure with locking lever.
The appliance is now prepared for wet cleaning.
몇 CAUTION
Always work with an inserted foam filter - during
wet as well as dry vacuum cleaning!
몇
CAUTION
Check the object to be cleaned prior to using the appli-
ance in an inconspicuous place for colour fastness and
water resistance.
Do not clean water-sensitive floor coverings such as
wood floors (the moisture could penetrate and damage
the floor).
NOTICE
Warm water (max. 50°C) will increase the cleaning ef-
fect.
 Use the wash floor nozzle.
 Work without the hard surface insert.
Please only use the carpet cleaner RM 519.
 Use the wash floor nozzle.
 Slide the attachment for hard surfaces onto the
spray ex floor nozzle from the side. The bristles
should point towards the back.
 Use the wash hand nozzle.
Note : You can remove the water reservoir to fill it or you
can fill it directly on the appliance.
Illustration

Flip the reservoir cover up.
 Add 100 - 200 ml (volume depends on degree of
contamination) of RM 519 into the fresh water res-
ervoir, then add tap water - do not overfill.
 Close the reservoir cover.
Illustration
 Insert the mains plug into the socket.
 Press the switch for suction (position I), suction tur-
bine is running.
Illustration
 Close fully the surrounding air separator at the han-
dle.
Illustration

Press the switch for spraying (position I), the deter-
gent pump is ready.
Illustration

Use the lever on the spray handle to spray on de-
tergent solution.
Illustration

For continuous spray, the spray lever can be
locked; for this, activate the spray lever and pull the
locking key toward the rear.

Run across the surface to be cleaned in overlap-
ping paths. Pull the nozzle backwards (do not
push).
Note: If the container is full, a float closes the suction
opening, and the appliance works at a higher speed.
Switch off the appliance immediately, and empty the
container.
 Switch the appliance off by pressing the switch for
suction and spraying (position 0).
 Separate the spray/suction hose and the spray
hose from the appliance.
Note : Possibly remaining water can drip out, there-
fore you should place these into the shower or
bathtub.
 Remove the accessories and the fresh water reser-
voir and unlatch the motor casing.
 Remove the motor casing and empty the reservoir.
– Always work from the light to the shade (from the
window to the door).
– Always work from the cleaned to the uncleaned
surface.
– Rugs with jute backing can shrink if too much water
is used and can bleed colours.
– Brush high-fiber rugs in the direction of the weave
after cleaning (using a fiber brush or a scrubber).
– Water-proofing the fabric using Care Tex RM 762
after the wet cleaning prevents a quick resoiling of
the textile surface.
– Do not step on cleaned surfaces until they have
dried and do not place furniture on them to avoid
pressure spots or rust stains.
 Turn on suction and spraying (position I).
 Spray and simultaneously suction off detergent so-
lution in one work cycle.
 Switch off the spray switch and suction off the re-
maining cleaning solution.
 After cleaning the carpets, reclean them using
clear, warm water and waterproof if needed.
 Switch on sprayer (position I).
 Apply detergent solution and allow to react for 5
minutes (vacuuming is switched off).
 Clean the surface just like you would with light/nor-
mal soiling.
 After cleaning the carpets, reclean them using
clear, warm water and waterproof if needed.
Operations
Wet cleaning
carpets/hard floors/upholstery
Wet cleaning of carpeted floors
Wet cleaning of hard surfaces
Wet cleaning of upholstery
Fill up fresh water reservoir
Start working
Emptying the reservoir during operation
Cleaning tips/mode of operation
Cleaning methods
Light/normal contamination
Heavy soiling or stains
12 EN