Kärcher HDS-E 8/16-4M 12kW, Руководство пользователя

Страница: 18 / 244

– 5
 Lock in the steel pipe into the holder of the appli-
ance hood.
 Roll up high pressure hose and electrical conduit
and hang them into the respective holders.
Note: Do not twist high pressure hose and electrical
conduit.
ATTENTION
Risk of damage! Frost will destroy the appliance if the
water has not been completely drained.
 Store in a frost free area.
If it is not possible to store frost free, shut down device.
For longer work breaks or if a frost free storage is not
possible:
 Empty detergent tank.
 Drain water.
 Flush device with anti-freeze agent.
 Screw off water supply hose and high pressure
hose.
 Unscrew the drain screw of the boiler on the bottom
of the boiler and empty the boiler.
 Operate device for max. 1 minute until the pump
and conduits are empty.
Note: Observe handling instructions of the anti-freeze
agent manufacturer.
 Fill commercial grade anti-freeze into the boiler.
 Switch on appliance (without heater) until the appli-
ance has been completely rinsed.
A certain corrosion protection is achieved with this as
well.
몇 CAUTION
Risk of personal injury or damage! Consider the weight
of the appliance when storing it.
Figure 6
ATTENTION
Risk of damage! When loading the appliance with a
forklift, observe the illustration.
ATTENTION
Protect the trigger from damage during transport.
몇 CAUTION
Risk of personal injury or damage! Mind the weight of
the appliance during transport.
 When transporting in vehicles, secure the appli-
ance according to the guidelines from slipping and
tipping over.
 DANGER
Risk of injury by inadvertent start-up of appliance and
electric shock. Prior to all work on the appliance, switch
off the appliance and pull the power plug.
 Shut off water supply.
 Open the hand spray gun.

Switch on the pump with the power switch and al-
low to run for about 5-10 seconds.
 Close the hand spray gun.
 Set the appliance switch to "0/OFF“.
 Pull main plug out of socket with dry hands only.
 Remove water connection.
 Activate hand spray gun until device is pressure
less.
 Secure the trigger gun. To do so, push the safety
catch towards the front.
 Allow device to cool down.
Your Kärcher vender will inform you about the per-
formance of a periodic safety inspection resp. sign-
ing of a maintenance contract.
 Clean the sieve in the water connection.
 Clean the fine filter.
 Check oil level.
ATTENTION
Risk of damage! In case of lacteous oil inform Kärcher
customer service immediately.
 Clean the sieve in the safety block.
 Clean filter at the detergent suck hose.
 Check the calcification degree of the boiler and
consider having it cleaned by customer service.
 Oil change.
 Have the maintenance of the device performed by
the customer service.

Take out sieve.
 Clean sieve in water and reinstall.
 Unpressurize the appliance.

Unscrew the fine filter from the boiler.
 Remove the fine filter and the filter insert.
 Clean the filter with clean water or compressed air.

Reinstall in reverse sequence.
 Unpressurize the appliance.
 Loosen covering nut and take off hose.

Take out sieve.
Note: If necessary turn in screw M8 appr. 5 mm inwards
and therewith pull out sieve.

Clean sieve in water.
 Push sieve inwards.
 Put on hose.

Tighten covering nut firmly.
 Take out detergent suck supports.
 Clean filter in water and reinstall.
Storing the Appliance
Frost protection
Shutdown
Dump water
Flush device with anti-freeze agent
Storage
Transport
Care and maintenance
Maintenance intervals
Weekly
Monthly
After 400 operating hours, at least annually
Every 500 operating hours, at least annually
Maintenance Works
Clean the sieve in the water connection
Cleaning the fine filter
Clean the sieve in the safety block
Clean filter at the detergent suck hose
18 EN