Kaco blueplanet 87.0 TL3 S Скачать руководство пользователя

Страница: 53 / 110

Country-
spec. Set-
tings

Level Display/

settings

Action in this menu/meaning

Frequency

NOTE: Opportunity to monitor frequency trip-off

Trip underfrequency
monitoring

Status

Activate, if necessary.

Number of underfre-
quency trip-off levels

1- 5

Specify the number of support levels.

Underfrequency trip-
off

42.5 – 65 [Hz] / &

underfrequency trip-off
time for levels 1 to 5

0 – 120000 [ms]

NOTE: If the grid frequency is within the deactivation range for the du-
ration of the deactivation time, then the function is deactivated.

Specify the range and trip-off time.

Trip overfrequency
monitoring

Status

Activate, if necessary.

Number of overfre-
quency trip-off levels

1- 5

Specify the number of support levels.

Overfrequency trip-off

45.0 – 67.5 [Hz] / &

overfrequency trip-off
time for levels 1 to 5

0 – 120000 [ms]

Password protection

Status

NOTE: If the grid frequency is within the deactivation range for the du-
ration of the deactivation time, then the function is deactivated.

1 Specify the range and trip-off time.

2 Activate optional password protection.

3 Confirm the action field.

KACO blueplanet 87.0 TL3 KACO blueplanet 92.0 TL3 KACO blueplanet 110 TL3 KACO blueplanet 125 TL3
KACO blueplanet 137 TL3 KACO blueplanet 150 TL3

Page 53

EN-US

Содержание blueplanet 87.0 TL3 S















































































































Результаты поиска

Содержание blueplanet 87.0 TL3 S

Отзывы:

Похожие инструкции для blueplanet 87.0 TL3 S

Бренды по названию

Популярные бренды

Kaco blueplanet 87.0 TL3 S, Руководство пользователя

Результаты поиска

Содержание blueplanet 87.0 TL3 S

Отзывы:

Похожие инструкции для blueplanet 87.0 TL3 S

Бренды по названию

Популярные бренды