K-TRON K-Vision Скачать руководство пользователя

Страница: 72 / 121

Alarm Messages- Cause and Remedy

4.1 System alarms

Page 72

Docu-No.: 0590020601-EN Rev. 1.6.0

23/01
HCU EEPROM
FAILED

• EEPROM failed.



Clear alarm.
Change EEPROM or HCU.



Cycle power to the HCU.

24/02
HCU DRIVER
FAILED

• The controller's digital output driver

has detected a fault.



Change HCU.



Latched.

25/03
HCU
SUPP.HOPP.LOW

• Material is below the level of the

supply hopper proximity sensor.

• Sensor failed.



Refill or change supply hopper.



Check P17.



Check sensor or P23.

Note:

Alarm will automatically clear

when material is above sensor.

26/04
HCU D.P.ALARM

• The differential pressure across the

filter is too high indicating a clogged
filter.



Clean or replace filter.



Check P24 and P16.



Check P17

27/05
HCU CYC.COUNT
AL

If P20 Discharge Mode =01“Fill” mode
then:

• Max. numbers of load cycle

exceeded, because Buffer Hopper
Low input has been active (on) for
more than the allowed load cycles.
The Buffer Hopper Low signal going
inactive clears the load cycle
counter.

If P20 Discharge Mode =02 (LWF)
mode then:

• Discharge Request input has been

on for more than the allowed load
cycles. The Discharge Request
signal going inactive clears the load
cycle counter.



Check Parameter P25 Number of
load cycles.



Check conveying rate.



Check Buffer hopper sensor.



Check Parameter P25 Number of
load cycles.



Check conveying rate.



Check discharge request signal.

28/06
HCU DISCH VALVE

• Discharge valve has failed to either

open or close properly. This alarm is
automatically disabled in P18
Operating Modes 03 and 04.



Check sensor on the discharge
valve.



Check P26

29/07
HCU REV.FULL AL.

• Receiver is still full after discharge.

• Receiver proximity switch too

sensitive adjusted or failed.



Check receiver. Material bridging in
the receiver. Clean receiver.



Check Receiver proximity switch or
P17.

Alarm Num- Alarm

Cause

Remedy

Table page 4 of 7

Содержание K-Vision


























































































































Результаты поиска

Содержание K-Vision

Отзывы:

Похожие инструкции для K-Vision

Бренды по названию

Популярные бренды

K-TRON K-Vision, Инструкция по программированию

Результаты поиска

Содержание K-Vision

Отзывы:

Похожие инструкции для K-Vision

Бренды по названию

Популярные бренды