K-TRON K-Vision Скачать руководство пользователя

Страница: 42 / 121

Programming Reference

1.7 Machine setup menu

Page 42

Docu-No.: 0590020601-EN Rev. 1.6.0

1.7.9

Motor sub-menu for HiPo, LoPo Stepper motor

This chart is used to program the HiPo and LoPo stepper drives, part
numbers 0000004568 and 0000001430 respectively.

Parameter

Definition

GEAR REDUC

Gear Reduction or Total

Gear Reduction

This parameter if entered as the gear reduction value between the
stepper motor and the disk/screw, results in the disk/screw speed
being displayed in the parameter <SCREW SPEED>.

Input range: 0 to 999

Default: 0

PICK UP TEETH

Speed Pickup Teeth

Input of the number of pulses per revolution of the optical encoder.

This encoder is used for measuring the speed.

Input range: 0 to 9999

Default: 400

MAX MOT SPEED - [rpm]

Maximum Motor Speed

Input of the maximum motor rpm for 100% drive command.

Input range: Drive specific.

Default: 60

(See table

1.7.10

for values)

MDU STATUS

MDU Status

The MDU status codes reveal operational condition of the Drive. See
listing of MDU status codes in section

5.4.1

DC CEILING-[%]

Drive Command Ceiling

Limitation of the drive command output to the motordrive.

Input range: 10 to 125%

Default: 100%

Содержание K-Vision


























































































































Результаты поиска

Содержание K-Vision

Отзывы:

Похожие инструкции для K-Vision

Бренды по названию

Популярные бренды

K-TRON K-Vision, Инструкция по программированию

Результаты поиска

Содержание K-Vision

Отзывы:

Похожие инструкции для K-Vision

Бренды по названию

Популярные бренды