K-TRON K-Vision Скачать руководство пользователя

Страница: 69 / 121

Docu-No.: 0590020601-EN Rev. 1.6.0

Page 69

Alarm Messages- Cause and Remedy

System alarms 4.1

Alarm Messages- Cause and Remedy

4.1

System alarms

• The associated number is the alarm number used for configuration

and data communication.

• The HCU is the control unit for the Hurricane vacuum material

loader for the feeder. It is programmed via the KSU-II/KCM and its
alarms are reported there.

• The first number is the KCM alarm, the second the HSU alarm.

(KCM#/HSU#). This code begins at KCM alarm (21) and ends at
KCM alarm (29).

Alarm Num- Alarm

Cause

Remedy

00 HARDWARE
ERROR

• KCM Hardware error. EEPROM

data is corrupt. For example, this
message will occur after updating or
changing firmware on the KCM.



Check KCM CPU.



Clear alarm and try unit.

01 KPROM MEM
FAIL

• The K-PROM cannot be accessed

by the KCM CPU.



Correctly insert K-PROM.



Replace with known good K-
PROM.

02
KPROM*KGR*FAIL

• Checksum error in kgr file area.



Verify K-PROM is properly
installed.



Replace K-PROM.

03 POWER GLITCH

• Power dip detected. CPU did not

reset.



Verify AC mains are within
specification.



Replace drive pcb (power supply).

04 KPROM WRITE
COUNT
EXCEEDED

• The K-Prom Write Counter exceeds

100'000 writes



Check communication.



Replace with known good K-
PROM.

05 INT CHAN FAIL

• Internal channel has failed to

communicate between the CPU and
drive boards. (also SFTs and HCU)



Check Internal Channel
connections.



Replace either CPU or Drive pcb.
(also check SFTs and HCU if used)

Table page 1 of 7

Содержание K-Vision


























































































































Результаты поиска

Содержание K-Vision

Отзывы:

Похожие инструкции для K-Vision

Бренды по названию

Популярные бренды

K-TRON K-Vision, Инструкция по программированию

Результаты поиска

Содержание K-Vision

Отзывы:

Похожие инструкции для K-Vision

Бренды по названию

Популярные бренды