K-TRON K-Vision Скачать руководство пользователя

Страница: 14 / 121

Programming Reference

1.1 Product change menu

Page 14

Docu-No.: 0590020601-EN Rev. 1.6.0

BULKDENSITY

Bulk Density

If the variable <VOL RATE>, in the <SERVICE VARIABLE INDEX>,
is set any value other than <0>, this variable will be displayed.

As the feeder runs in gravimetric control, the Bulk Density value will
be updated by the calculation: BD = FF/VOL RATE

Note:

To use this variable, do the following:

1. Enter the bulk density (BD) of the material being fed.

2. Perform an Auto Feedfactor calibration. The result is the value

<VOL RATE>, calculated as the ratio of Feedfactor (FF) /
Entered Bulk Density. The value <VOL RATE> is found in the
Service Variable Index.

When the feeder runs in gravimetric control, the <BULKDENSITY>
parameter will reflect the current material bulk density.

EMPTY FDR

Empty feeder function. When started, the feeder runs at a drive
command of 70%. The feeder stops automatically if no weight loss is
detected.

Note:

<Empty Drive Cmd> may be changed by the Service Variables.

▲

This command will start the feeder. Make sure that nobody is
working on the machine.



For KSU-II/KCM select EMPTY FDR, then press

ENTER

twice then

RUN



For KSL press

MORE-F5

- then press

then press

RUN



For KSC, press the

then

RUN

Notes:

• The <EMPTY FDR> action can be halted with the

STOP

key.

• The Net Weight Low alarm is also generated when the Empty Fdr

cycle finishes.

Parameter

Definition

Table page 4 of 5

Содержание K-Vision


























































































































Результаты поиска

Содержание K-Vision

Отзывы:

Похожие инструкции для K-Vision

Бренды по названию

Популярные бренды

K-TRON K-Vision, Инструкция по программированию

Результаты поиска

Содержание K-Vision

Отзывы:

Похожие инструкции для K-Vision

Бренды по названию

Популярные бренды