K-TRON K-Vision Скачать руководство пользователя

Страница: 52 / 121

Programming Reference

1.8 I/O Menu

Page 52

Docu-No.: 0590020601-EN Rev. 1.6.0

1.8.4

Analog output sub-menu

• The KCM CPU only outputs a 0-20 mA current value. Use

appropriate resistors to convert to the desired voltage.

• Maximum source voltage is 12 Vdc for the current output.

• For calibration, see section

3.2

Refer to KCM Electronics manual for more information on electrical
connections and operational limitations.

Parameter

Definition

AOUT NUM

Analog Output

Selection of the desired analog output for the KCM.

Select: CPU, EXT1 - EXT3.

Input range: See list

Note:

For Ext1-Ext3 functions to work, Modbus I-O must be configured first
and the external I-O module (e.g.WAGO) connected via K-Port 2.

FUNCTION

Analog Output Function

The analog output can be assign with the following function:

SETPOINT

(20mA/Max. setpoint) x Actual setpoint

MASSFLOW

(20mA/Max. setpoint) x Massflow

NETWEIGHT

(20mA/Scale range) x net weight

DRIVE COMMAND

(20mA/100%) x Percent drive command

MOTOR SPEED

(20mA/

Max Mot RPM) x Act Mot Spd

FEEDFACTOR

(12mA/Init FeedFactor) x actual feedfactor)

Input range: See list Default: None

AOUT VALUE%]

Analog Output Value%

Display of the actual output value in percentage of the maximum
value.

Input range: Display only

AOUT MIN

Analog Output Minimum

Scaling of the analog output for the minimum value. (Offset
adjustment e.g. 20% for 4 mA)

This value can be used also to invert the analog output.

Input range: 0 to *100% (*Inverted 100%)

AOUT MAX.

Analog Output Maximum

Scaling of the analog output for the maximum value.

This value can be used also to invert the analog output.

Input range: 100 to *0%

Default: 100% (*Inverted 0%)

DEABAND-[%]

Analog Output Deadband

Input of the deadband in percentage of the maximum value.
Changes at the output below this value will have no change to the
process value.

Input range: 0 to 100%

Default: 0%

Содержание K-Vision


























































































































Результаты поиска

Содержание K-Vision

Отзывы:

Похожие инструкции для K-Vision

Бренды по названию

Популярные бренды

K-TRON K-Vision, Инструкция по программированию

Результаты поиска

Содержание K-Vision

Отзывы:

Похожие инструкции для K-Vision

Бренды по названию

Популярные бренды