JVC KA-MR100G, Инструкция по эксплуатации

Страница: 18 / 20

15
Other s
Trouble s hooting
Symptom Cau s e( s ) Action s Refer to
Power does not turn
on Power is supplied from the DC INPUT
terminal of the camcorder. Attach the battery. The power of the memory recorder
cannot be supplied from the DC INPUT terminal of the
camcorder.
A
Page 7
Only the power of the camcorder is turned
A On B .
It is necessary to turn on the power of the memory recorder
at the same time.
A
Page 7
Remaining battery level is insufficient. Charge the battery.
A
Page 14
Unable to record or
play clip The IEEE1394 cable is not connected. Connect a GY-HD200/HD250 series camcorder to the
KA-UM100G adapter using an IEEE1394 cable.
A
Page 7
The [INT/EXT] switch setting of the
KA-UM100G adapter is inappropriate.
●
Set to A EXT B during normal use. (When IEEE1394
connection is made internally without the use of an
external cable, set to
A
INT
B
.
●
If the A NO SIGNAL B message does not disappear even
if the setting is correct, set the switch again to select the
setting. If the message remains displayed, turn off and
on the power again.
A
Page 7
The video formats of the camcorder and
memory recorder are not consistent with
each other. Ensure that the video format of the camcorder and memory
recorder are consistent with each other.
A
Page 9
The [IEEE1394] switch of the camcorder is
set to the
A DV B end.
Set the [IEEE1394] switch to the A HDV B end.
If the A NO SIGNAL B message does not disappear even
after setting to
A
HDV
B
, set the switch again. If the message
remains displayed, turn off and on the power again.
A
Page 9
A
Page 10
Recording does not
start The camcorder is set to the A VTR B mode. Set to the A CAM B mode using the [CAM/VTR] button.
A
Page 9
The [1394 REC TRIGGER] item on the
OTHERS[2/2] menu screen of the
camcorder is set to
A OFF B or A SERIES B .
Set [1394 REC TRIGGER] to A SYNCRO B or A SPLIT B .
When this is set to A SERIES B , recording starts when the
remaining capacity of the cassette tape falls below three
minutes.
A
Page 9
The memory recorder is set to the playback
mode. Press the [STOP] button to stop playback.
A
Page 9
The write-protect of the SxS memory card
is enabled. Set the write-protect switch to A Off B before recording or
deleting a clip.
A
Page 14
There is no space left on the SxS memory
card. Use an SxS memory card that has sufficient space.
A
Page 14
Unable to play clip The camcorder is set to the A CAM B mode. Set to the A VTR B mode using the [CAM/VTR] button.
A
Page 10
The cassette tape is currently being played
back. Stop playback of the cassette tape before playing back
data on the SxS memory card.
A
Page 10
A clip without the check mark (v) is
selected. Set the camcorder and memory recorder according to the
video format displayed when a clip is selected.
A
Page 10
The memory recorder is in the recording or
standby mode. Press the [STOP] button to stop playback.
A
Page 10
The clip may be damaged. Execute A RESTORE B using this memory recorder.
A
Page 14
No response when a
button is pressed The [OPERATION] menu is set to
A
LOCK
B
. Change the [OPERATION] menu setting to
A
UNLOCK
B
.
A
Page 14
A multiple number of buttons are pressed
at the same time, or the same button is hit
repeatedly. Insert a short pause between each button operation.
^
Access lamp does not
turn on The SxS memory card is not completely
inserted into the card slot. Make sure that the SxS memory card is fully inserted into
the slot.
A
Page 8
The SxS memory card is inserted with the
label facing the opposite direction. Identify the face of the SxS memory card with the label,
and make sure that the card is correctly oriented before
inserting.
A
Page 8
SxS memory card
cannot be used A SxS memory card that is formatted by
another device is used. Execute A FORMAT B using this memory recorder.
A
Page 13
A media that is not supported is inserted. Replace it with a recommended SxS memory card.
A
Page 14
The clip is faulty. Execute A RESTORE B or A FORMAT B using this memory
recorder. If doing so does not eliminate the error, replace it
with a recommended SxS memory card.
A
Page 14
Error message
appears on the
camcorder panel
display A DR-HD100 POWER ? B appears when the
memory recorder is not powered on or is
not connected.
Connect and turn on the power of the memory recorder.
A
Page 6
A
Page 7
A
HDD NO 1394 SIGNAL
B
appears if the
camcorder is set to the “CAM” mode when
the memory recorder is in playback mode.
Set the camcorder to the
A
VTR
B
mode.
A
Page 10
A HDD SPACE LOW B appears when the
space on the SxS memory card is
insufficient or an SxS memory card is not
inserted.
Use an SxS memory card that has sufficient space.
^
KA-MR100G_EN.book Page 15 Thursday, February 5, 2009 5:28 PM