Juniper TCX1000 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 25

Juniper TCX1000 Скачать руководство пользователя страница 25

Revision History

December 2018—Updated revision. Updated the Perform the Initial Configuration section.

November 2018—Updated revision. Added Step 10 “Enabling OSC Forwarding on the
TCX1000-RDM20”.

June 2018—Updated revision. Revised the sample output in the “Perform the Initial
Configuration” section.

February 2018—Updated revision. Revised the Compliance statements for NEBS and
Perform the Initial Configuration sections.

December 2017—Initial revision.

Copyright © 2018, Juniper Networks, Inc. All rights reserved.

Juniper Networks, the Juniper Networks logo, Juniper, and Junos are registered trademarks of Juniper Networks, Inc. and/or its affiliates in
the United States and other countries. All other trademarks may be property of their respective owners.

Juniper Networks assumes no responsibility for any inaccuracies in this document. Juniper Networks reserves the right to change, modify,
transfer, or otherwise revise this publication without notice.

25

Copyright © 2018, Juniper Networks, Inc.

Requesting Technical Support

«
...
23
24
25

Содержание TCX1000


























Отзывы:

Нет отзывов