Juniper JUNOSe 11.0.1 Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 124

background image

Errata

61

Release 11.0.1

Errata

This section identifies errors found in the JUNOSe documentation. These errors are
corrected in subsequent releases of the affected documentation.

The

Obtaining Documentation

section in the

About the Documentation

chapter of

every JUNOSe document erroneously indicates that MIBs are available on the
JUNOSe Software CDs. MIBs are available for a particular software release only
from the software image bundle that is available for download from the Juniper
Networks website. We are no longer providing software CDs beginning with
JUNOSe Release 11.0.0.

The Policy and QoS Maximums (for E120 and E320 routers) table in

JUNOSe

Release Notes

,

Appendix A, System Maximums

for Releases 9.x, 10.x, and 11.0.x

incorrectly states that the maximum number of policy classification (CLACL)
entries for the ES2 10G Uplink LM is 131,171.

The correct limit for CLACL entries for the ES2 10G Uplink LM in these releases
is 65,535.

In the

Change in existing behavior

section

of the

System

category in the

Release

Highlights

section of the

JUNOSe 11.0.0 Release Notes,

the term "our" in the last

sentence is misspelled. It is now corrected to read as "your".

The

ERX Module Guide, Appendix A, Module Protocol Support

incorrectly states

that IPv6 multicast is supported on the following line modules:

cOCx FO line module with cOC3/STM1 modules

cOCx FO line module with cOC12/STM4 FO I/O modules

COCx-F3 line modules with CT3/T3 12 I/O modules

OCx/STMx ATM line modules with 4xDS3 ATM I/O modules

CT3/T3-FO line modules with CT3/T3 12 I/O modules

ERX Module Guide, Appendix B, Module Name Cross-Reference Information

fails to

include all ERX routers listed in the E Series Broadband Services Routers
datasheet dated December 2009. See

Appendix B, Module Name Cross-Reference

Information,

in these Release Notes

for a single table that lists the module label

name, software display name, and the model number for each module for all
ERX routers listed in the datasheet.

The

E120 and E320 Module Guide, Appendix A, IOA Protocol Support

incorrectly

states that IPv6 multicast is supported on the ES2-S1 Service IOA module. IPv6
multicast is not supported on this module.

«
...
67
68
69
70
71
...
»

Содержание JUNOSe 11.0.1





























































































































Отзывы:

Нет отзывов

Похожие инструкции для JUNOSe 11.0.1

Бренд: Canon Страницы: 2

Pixma Pro9500 Series

Бренд: Canon Страницы: 31

PowerShot SD430 DIGITAL ELPH WIRELESS

Бренд: Canon Страницы: 130

PowerShot SD880 IS Digital ELPH

Бренд: Canon Страницы: 83

Бренд: Canon Страницы: 34

N1240U - CanoScan Flatbed Scanner

Бренд: Canon Страницы: 109

Бренд: 3Com Страницы: 4

Бренд: Navman Страницы: 10

Бренд: Teklynx Страницы: 30

Бренд: Novell Страницы: 126

APPLICATION STACK 2.0 RELEASE

Бренд: Red Hat Страницы: 26

NETWORK SATELLITE SERVER 4.0

Бренд: Red Hat Страницы: 80

NETWORK - USER REFERENCE GUIDE 3.1

Бренд: Red Hat Страницы: 78

NETWORK SATELLITE 5.1.0 - CHANNEL MANAGEMENT

Бренд: Red Hat Страницы: 300

Бренд: NETGEAR Страницы: 282

Бренд: Blackberry Страницы: 9

ENHANCED GOOGLE MAIL PLUG IN - LEARN MORE

Бренд: Blackberry Страницы: 16

PRD-10459-003 - Enterprise Server For IBM Lotus Domino

Бренд: Blackberry Страницы: 420

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды