Juniper JUNOSe 11.0.1 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 124

background image

Early Field Trial Features

9

Release 11.0.1

host1(config)#

no ip dhcp-local limit pos

To display the maximum number of IP address leases available for POS access
interfaces, use the existing

show ip dhcp-local limits

command. For example:

host1#

show ip dhcp-local limits

*****************************************
     DHCP Local Server Address Limits
ATM Limit     - 48000
VLAN Limit     - 48000
POS Limit     - 1000
Ethernet Limit - 48000

IPv6

Support for Configuring IPv6 HTTP Redirect URL from Profile Configuration
Mode

You can now provide initial provisioning and service selection for the
subscriber, by using the IPv6 HTTP redirect URL feature. You use the

ipv6 http

redirectUrl

command from the Profile Configuration mode to specify the URL

to which a subscriber’s initial Web browser session is redirected, as shown in
this example:

host1(config)#

profile guidEnt6

host1(config-profile) #

ipv6 http redirectUrl http://ispite.redirect.com

The following commands have been enhanced to support this feature:

In the current release, this feature is available for early field test purposes only.

System Maximums

Increased Number of Service Sessions and Subscriber Sessions for E120 and
E320 Routers

Beginning with JUNOSe Release 11.0.0, the maximum number of service
sessions and subscriber sessions that are supported per chassis for the Service
Manager application on E120 and E320 routers are as follows:

In the current release, this feature is available for early field test purposes

only.

ipv6 http redirectUrl

show profile

Number of Service and Subscriber
Sessions per Chassis for Service
Manager

E120 Limits

E320 Limits

Service sessions (active)

196,608

262,144

Active subscriber sessions

64,000

96,000

«
...
15
16
17
18
19
...
»

Содержание JUNOSe 11.0.1





























































































































Отзывы:

Нет отзывов

Похожие инструкции для JUNOSe 11.0.1

eTrex H - Hiking GPS Receiver

Бренд: Garmin Страницы: 100

Бренд: Yamaha Страницы: 11

ZENworks Network Access Control 5.0

Бренд: Novell Страницы: 534

PlateRunner P24 Processor

Бренд: Xante Страницы: 6

Бренд: TruCluster Страницы: 88

Бренд: Yamaha Страницы: 4

Бренд: Yamaha Страницы: 6

Бренд: Yamaha Страницы: 7

Бренд: Yamaha Страницы: 9

Бренд: Yamaha Страницы: 11

Бренд: Yamaha Страницы: 15

Бренд: Yamaha Страницы: 14

Бренд: Yamaha Страницы: 72

Бренд: Yamaha Страницы: 129

Diabetes Management Software v2.2

Бренд: OneTouch Страницы: 13

Бренд: Cabletron Systems Страницы: 92

Бренд: APPLIED ACOUSTICS SYSTEMS Страницы: 60

NORTON INTERNET SECURITY - FOR MAC V4

Бренд: Symantec Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды