Juniper JUNOSe 11.0.1 Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 124

background image

JUNOSe 11.0.1 Release Notes

44

Known Problems and Limitations

In a network where you use the tunnel signalling command to specify that the
security parameters and keys are configured manually for IPSec tunnels
between VRs, the line modules reset when you delete and then re-create the
IPSec tunnels. If you attempt to configure the tunnels again after the modules
come back up, the line modules reset again.

Work-around

: Configure the IPSec tunnels to use ISASKMP/IKE to negotiate SA

and establish keys. [Defect ID 178304]

IPSec tunnels created over Fast Ethernet interfaces fail to come up. [Defect ID
179256]

Work-around:

After you create the tunnel, bounce the tunnel interface by

issuing the

shutdown

/

no shutdown

command sequence. The tunnel comes up

successfully.

IS-IS

On a router configured with IS-IS and BFD, using the

redundancy force srp

command to force an SRP switchover sometimes brings down IS-IS and BFD.
[Defect ID 179287]

IS-IS graceful restart (nonstop forwarding) does not work on the broadcast
interface when the restarting router is the designated intermediate system
(DIS). Graceful restart works properly when the restarting router is not the DIS.
[Defect ID 61496]

L2TP

After a unified ISSU completes on a router functioning as an L2TP access
concentrator (LAC), traffic outages occur on the L2TP network server
(LNS)-facing interface at the LAC in a configuration with 16,000 or 32,000 L2TP
sessions over 500 tunnels. [Defect ID 180147]

MLD

MLDv2 proxy is not supported. [Defect ID 46038]

The E Series router MLDv2 proxy does not operate correctly in the presence of
MLDv1 queriers. [Defect ID 46039/46045]

Work-around:

If an MLDv1 router is present on the network, configure version

1 with the

ipv6 mld-proxy version

command on that network interface.

(Version 2 is the default.)

The default value for the MLDv2 proxy unsolicited report interval timer should
be 1 second rather than 10 seconds (the value for v1). [Defect ID 46040]

The E Series router does not log a warning when it receives an MLDv1 query
but is not configured to use MLDv1 on the interface. [Defect ID 46046]

«
...
50
51
52
53
54
...
»

Содержание JUNOSe 11.0.1





























































































































Отзывы:

Нет отзывов

Похожие инструкции для JUNOSe 11.0.1

Бренд: Xerox Страницы: 28

TRANSCEND EM/NT 6.3

Бренд: 3Com Страницы: 39

Бренд: Accordiva Страницы: 31

Бренд: Quantum Страницы: 26

Management Console 4.4

Бренд: Quantum Страницы: 120

Бренд: Nortel Страницы: 41

BayStack 380-24F

Бренд: Nortel Страницы: 76

Бренд: Nortel Страницы: 176

Express Call Center

Бренд: Nortel Страницы: 638

Symposium Web Center Portal

Бренд: Nortel Страницы: 710

Бренд: ESET Страницы: 38

STRM 2008-2 - TECHNICAL NOTE CHANGING NETWORK SETTING 6-2008

Бренд: Juniper Страницы: 14

PowerSuite 2010

Бренд: UNIBLUE Страницы: 13

SpeedUpMyPC 2010

Бренд: UNIBLUE Страницы: 11

Terminal Emulation TN5250

Бренд: IBM Страницы: 51

VIAVOICE 10-ADVANCED EDITION

Бренд: IBM Страницы: 126

Бренд: FARONICS Страницы: 2

Бренд: Sun Microsystems Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды