Juniper JUNOSe 11.0.1 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 124

background image

Known Behavior

27

Release 11.0.1

When you install an ES2-S1 Redundancy IOA with a hardware revision number
of -02 or less in slot 0 or slot 11 of the E320 router or in slot 0 or the E120
router, do not install an OCx/STMx ATM IOA or an OCx/STMx POS IOA in the
lower (E320) or left (E120) adapter bay of slot 1 or slot 12. When the spare line
module is controlling another slot and you revert back to the primary line
module, the ATM or POS IOAs can become unusable or cause the line module to
reset. [Defect ID 69760]

Work-around:

This problem is not present for ES2-S1 Redundancy IOAs with a

hardware revision number of -03 or higher.

MLPPP

Do not configure both MLPPP fragmentation (with the

ppp fragmentation

command) and IP fragmentation of L2TP packets (with the

ip mtu

command)

on the same interface. Instead, you must choose only one of the fragmentation
configurations by setting it to the necessary value and set the other
fragmentation configuration to the maximum allowable value.

MPLS

Martini circuits configured on the ES2 10G LM act as true layer 2 tunnels,
without modifying the layer 2 headers. For this reason, Martini VLAN retagging
is not currently supported.

If you are upgrading to Release 7.1.0 or a higher-numbered release from a
release numbered lower than Release 7.1.0, and have inter-AS option B or C
configurations, you must explicitly configure MPLS on all inter-AS links, as in
the following example:

host1#

configure terminal

host1(config)#

interface fastEthernet 2/0

host1(config-if)#

ip address

...

host1(config-if)#

mpls

If you do not explicitly configure MPLS on the links, the inter-AS feature will not
work properly.

Multicast

The

ip dipe sg-cache-miss

and

ipv6 dipe

commands are not intended or

supported for customer use, although they are visible in the User Exec and
Privileged Exec modes respectively. These commands are intended to be used
in a Juniper Networks internal lab environment for testing without a traffic
generator.

Do not configure a multicast group with more than 10,219 outgoing interfaces
(OIFS) on the same ES2 10G LM. The configuration of the multicast group’s OIF
membership from the SRP module to the line module exceeds the size of a
single message and is sent in fragments. Because of this fragmentation, the ES2
10G LM generates the following error message: [Defect ID 81768]

pc: 0x9e5c88: -> fatalPanic(void) offset: 0x8

«
...
33
34
35
36
37
...
»

Содержание JUNOSe 11.0.1





























































































































Отзывы:

Нет отзывов

Похожие инструкции для JUNOSe 11.0.1

COLDFUSION MX 61-CFML

Бренд: MACROMEDIA Страницы: 34

Бренд: Nero Страницы: 76

Afro-Cuban Percussion

Бренд: M-Audio Страницы: 5

WINDOWS LIVE MESSENGER - LEARN MORE

Бренд: Blackberry Страницы: 18

Universal Storage Platform VM

Бренд: Hitachi Страницы: 62

Universal Storage Platform V

Бренд: Hitachi Страницы: 102

Бренд: Hitachi Страницы: 205

Бренд: Canon Страницы: 40

Бренд: Canon Страницы: 97

ScanGear CS-S 4.3

Бренд: Canon Страницы: 109

CanoScan FS2700F

Бренд: Canon Страницы: 80

Digital Video Software (Windows)

Бренд: Canon Страницы: 89

Бренд: Canon Страницы: 98

Бренд: Canon Страницы: 88

Бренд: Canon Страницы: 168

Digital Camera Solution Disk V.27

Бренд: Canon Страницы: 130

Viewer for Pocket PC RV-P1.0

Бренд: Canon Страницы: 22

Бренд: Canon Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды