Juniper JUNOSe 11.0.1 Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 124

background image

JUNOSe 11.0.1 Release Notes

54

Known Problems and Limitations

Unified ISSU

ATM line modules might reset after a unified ISSU when you attempt to add
memory to a VLAN subinterface in a large bridged Ethernet configuration.
[Defect ID 178798]

Under certain conditions, a unified ISSU from JUNOSe Release 9.2.0p1-0 to the
current release fails, and causes the SRP module and the ES2 4G LM to reset.
[Defect ID 179975]

When any of the subsystems is excluded for a JUNOSe release, a unified ISSU to
that release fails to apply conversion code to all of the line modules. As a result,
the line modules reset when they come up with that release. [Defect ID
179595]

Work-around:

To prevent the exclusion of a subsystem file from the release, do

the following before you upgrade to a new JUNOSe release that supports unified
ISSU:

1.

Issue the

show subsystems file

fileName

.rel

command, where

fileName

is

the name of the software release file, to determine whether any of the
subsystem files are excluded from the release.

2.

For each subsystem file that is excluded, issue the

no exclude-subsystem

subsystemName

command to remove the exclusion for the specified

subsystem file.

If you copied the software release to the router before removing the subsystem
file from the exclusion list, you must copy the release to the router again to
ensure that all subsystem files are included in the release.

Unified ISSU is not supported with 8000 bridged Ethernet interfaces on an
OC3/STM1 GE/FE ATM line module. [Defect ID 179547]

During the unified ISSU operation, if you modify the router configuration after
the initialization phase of the process is completed and before you issue the

issu start

command to commence the upgrade phase of the unified ISSU

process, the unified ISSU procedure completes successfully and the stateful SRP
switchover process begins to synchronize between the active and standby SRP
modules. When the synchronization process is in progress, the standby SRP
module reloads for the second time. After the second reload of the standby SRP
module ends, the synchronization process also ends properly.

Although the standby SRP module reloads for the second time when it is
synchronized with the upgraded release, normal router operations, such as
handling of subscriber sessions and forwarding of traffic, remain unaffected.
[Defect ID 185517]

«
...
60
61
62
63
64
...
»

Содержание JUNOSe 11.0.1





























































































































Отзывы:

Нет отзывов

Похожие инструкции для JUNOSe 11.0.1

Бренд: TANDBERG Страницы: 66

Content Server None

Бренд: TANDBERG Страницы: 14

AUTOCAR CIVIL 2010

Бренд: Autodesk Страницы: 6

Бренд: COMPRO Страницы: 18

Бренд: TruCluster Страницы: 88

Бренд: Nortel Страницы: 41

BayStack 380-24F

Бренд: Nortel Страницы: 76

Бренд: Nortel Страницы: 176

Express Call Center

Бренд: Nortel Страницы: 638

Symposium Web Center Portal

Бренд: Nortel Страницы: 710

Бренд: Black Box Страницы: 65

IRISPowerscan 9.5

Бренд: I.R.I.S. Страницы: 182

Бренд: MGI Страницы: 19

Бренд: GRASS VALLEY Страницы: 4

Бренд: FieldServer Страницы: 29

Бренд: Bay Networks Страницы: 104

Unified Messaging

Бренд: Oracle Страницы: 46

Retail Place 12.2

Бренд: Oracle Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды