Juniper JUNOSe 11.0.1 Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 124

background image

Known Problems and Limitations

51

Release 11.0.1

Work-around

: To avoid this problem, use the

show service-management

owner-session

ownerName ownerId

command to display subscriber session

information based on the session owner, instead of the

show

service-management subscriber-session

subscriberName

interface

interfaceType

command to display details on subscriber sessions.

SNMP

When you configure the router with an address pool that has two IP address
ranges, only the range that you configured first is available via the MIB. [Defect
ID 61232]

SONET

You cannot use the highest sensitivity bit-error rate setting (a value of 9)
associated with APS/MSP alarm when you issue the

threshold sd-ber

command to configure a cOCx/STMx line module with cOC12-APS-capable
IOAs. [Defect ID 72861]

Work-around:

Use only a value in the range 5–8 when you issue the

threshold

sd-ber

command for this module combination, as in the following example:

host1(config)#

controller sonet 2/1

host1(config-controll)#

aps group boston

host1(config-controll)#

aps protect

host1(config-controller)#

threshold sd-ber 6

SRC Software and SDX Software

The SRC client does not prevent you from changing the name of the router
while the client is connected to the SAE, resulting in SAE issues such as lost IP
addresses and stale users. [Defect ID 77102]

Work-around:

To change the router name while the SRC client is connected to

the SAE, shut down the SRC client, change the name, then re-enable the SRC
client.

When multiple IPv6 interfaces are configured with policies attached from SRC,
only some of the IPv6 interfaces have the policies attached. [Defect ID 179498]

Changing the SSCC status (enable/disable) while IPv6 interfaces are configured
might cause the SRP to reset. [Defect ID 179537]

Stateful SRP Switchover (High Availability) and IP Tunnels

When you issue

show

commands as soon as the CLI is available after a stateful

SRP switchover, the commands can hang until the warm restart is completed.
[Defect ID 85306]

A packet loss sometimes occurs during stateful SRP switchover when you use
the

ping

command on a router that is configured for OSPF graceful restart, and

is connected to a helper router in the OSPF IPv6 broadcast network and
another helper router in the OSPF IPv6 backbone area. [Defect ID 181470]

«
...
57
58
59
60
61
...
»

Содержание JUNOSe 11.0.1





























































































































Отзывы:

Нет отзывов

Похожие инструкции для JUNOSe 11.0.1

GPSMAP GPSMAP 196

Бренд: Garmin Страницы: 4

Бренд: Garmin Страницы: 2

Бренд: Arturia Страницы: 125

Бренд: deXlan Страницы: 17

Бренд: TC Electronic Страницы: 22

Бренд: Brocade Communications Systems Страницы: 40

Brocade BladeSystem 4/24

Бренд: Brocade Communications Systems Страницы: 62

Fabric OS v7.0.1

Бренд: Brocade Communications Systems Страницы: 1132

Call Detail Reporting

Бренд: Altigen Страницы: 97

Altiware OE 4.5

Бренд: Altigen Страницы: 455

Wireless PCI Adapter Driver

Бренд: 2Wire Страницы: 4

SimpleDrive SP-U25/120

Бренд: SimpleTech Страницы: 8

Voyager Digital Media Player

Бренд: BT Страницы: 30

Бренд: Acroprint Страницы: 61

Бренд: M-Audio Страницы: 88

Бренд: Pantone Страницы: 12

256B1-05A761-1301 - AutoCAD Revit Structure Suite 2010

Бренд: Autodesk Страницы: 1638

Бренд: Bay Networks Страницы: 112

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды