Jungheinrich EZS 330 XL, Руководство по эксплуатации

Страница: 49 / 85

0406
.GB
E 22
6.5 Travel parameters
Z
For trucks without a display instrument (CANDIS (
o
)) the code lock parameters can
only be set by the manufacturer's service department.
The following example shows the parameter setting for the acceleration of travel
program 1 (parameter 101).
Acceleration example
Enter the three-digit parameter number (101) and confirm with the Set key (45).
– Check the LC display of the display instrument (CANDIS (
o
)) (parameter number
and current parameter value are displayed).
Z
If there is no input for approx. 5 seconds, the display switches back to showing the
operating hours.
F
If you require a different parameter number than the one displayed, you must wait
until the operating hours are displayed again.
Enter or change the parameter value according to the parameter list.
Check the LC display of the indicator instrument (CANDIS (
o
)), (confirm with the Set
key (45).
– The LED (44) of the
o
key (43) switches briefly to steady light and start flashing
again after approx. 2 seconds.
Z
If the entry is incorrect, the LED (44) of the
o
key (43) goes red. If you enter the
parameter number again the setting can be entered or changed.
Repeat the procedure to enter further parameters as soon as the LED (44) of the
o
key (43) flashes. To complete your entry, press the
o
key (43).
Display instrument
(CANDIS)
LED (44)
o
key
LED (40)
Key 1
LED (41)
Key 2
LED (42)
Key 3
current setting is
displayed
101 6
Green
flashing
Off Off Off
Display instrument
(CANDIS)
LED (44)
o
key
LED (40)
Key 1
LED (41)
Key 2
LED (42)
Key 3
changed setting is
displayed
101 8
Green
flashing
Off Off Off
Display instrument
(CANDIS)
LED (44)
o
key
LED (40)
Key 1
LED (41)
Key 2
LED (42)
Key 3
Parameter
number
Parameter
setting
0406
.GB
E 22
6.5 Travel parameters
Z
For trucks without a display instrument (CANDIS (
o
)) the code lock parameters can
only be set by the manufacturer's service department.
The following example shows the parameter setting for the acceleration of travel
program 1 (parameter 101).
Acceleration example
Enter the three-digit parameter number (101) and confirm with the Set key (45).
– Check the LC display of the display instrument (CANDIS (
o
)) (parameter number
and current parameter value are displayed).
Z
If there is no input for approx. 5 seconds, the display switches back to showing the
operating hours.
F
If you require a different parameter number than the one displayed, you must wait
until the operating hours are displayed again.
Enter or change the parameter value according to the parameter list.
Check the LC display of the indicator instrument (CANDIS (
o
)), (confirm with the Set
key (45).
– The LED (44) of the
o
key (43) switches briefly to steady light and start flashing
again after approx. 2 seconds.
Z
If the entry is incorrect, the LED (44) of the
o
key (43) goes red. If you enter the
parameter number again the setting can be entered or changed.
Repeat the procedure to enter further parameters as soon as the LED (44) of the
o
key (43) flashes. To complete your entry, press the
o
key (43).
Display instrument
(CANDIS)
LED (44)
o
key
LED (40)
Key 1
LED (41)
Key 2
LED (42)
Key 3
current setting is
displayed
101 6
Green
flashing
Off Off Off
Display instrument
(CANDIS)
LED (44)
o
key
LED (40)
Key 1
LED (41)
Key 2
LED (42)
Key 3
changed setting is
displayed
101 8
Green
flashing
Off Off Off
Display instrument
(CANDIS)
LED (44)
o
key
LED (40)
Key 1
LED (41)
Key 2
LED (42)
Key 3
Parameter
number
Parameter
setting