Jungheinrich EJE 220 Скачать руководство пользователя страница 158

Страница: 158 / 232

4.3.2

Cleaning the electrical system assemblies

CAUTION!

Risk of electrical system damage

Cleaning the assemblies (controllers, sensors, motors etc.) of the electronic system
with water can damage the electrical system.

Do not clean the electrical system with water.

Clean the electrical system with weak suction or compressed air (use a
compressor with a water trap) and not a conductive, anti-static brush.

Cleaning the electrical system assemblies

Requirements

– Prepare the truck for maintenance and repairs (see page 154).

Tools and Material Required

– Compressor with water separator
– Non-conductive, antistatic brush

Procedure

• Expose the electrical system, see page 159.
• Clean the electrical system assemblies with weak suction or compressed air (use

a compressor with a water trap) and not a conductive, anti-static brush.

• Fit the electrical system panel, see page 159.
• Carry out all the tasks in the section "Recommissioning the truck after cleaning or

maintenance work" (see page 166).

The electrical system assemblies are now clean.

158

04.19 en-GB

Содержание EJE 220









































































































































































































































Результаты поиска

Содержание EJE 220

Отзывы:

Бренды по названию

Популярные бренды

Jungheinrich EJE 220, Руководство по эксплуатации

Результаты поиска

Содержание EJE 220

Отзывы:

Бренды по названию

Популярные бренды