manualshive.com logo in svg

Jungheinrich EJE 220, Руководство по эксплуатации

Поделиться
Скачать
Jungheinrich EJE 220 Скачать руководство пользователя страница 125

7.4

Setting the truck parameters with CanCode

CAUTION!

Incorrect input

Without  CanDis,  only  CanCode  internal  parameters  can  be  changed.  Traction
controller parameters can be changed only with CanDis; without CanDis, the settings
must be configured by the manufacturer's service department.

CAUTION!

Altering settings for the travel and hydraulic functions can result in accidents

Increasing the settings for travel and hydraulic functions can result in accidents.

u

Carry out a test run in a secure environment.

u

This requires greater attention on the part of the operator.

Parameter-setting example

The  following  example  shows  the  parameter  setting  for  the  acceleration  of  travel
program 1 (parameter 0256).

Acceleration example

Procedure

• Enter four-digit parameter number "0256" and confirm with the Set key (67).
• Enter subindex (enter "2") and confirm with the Set key (67).

Z

The  parameter  and  sub  index  are  displayed  alternately  with  the  current  reading
(0256-2<->0000-3).

• Enter the parameter according to the parameter list and confirm with the Set key

(67).

Z

The  LED  (68)  of  the  O  key  (69)  switches  briefly  to  continuous  light  and  starts
flashing again after 2 seconds.

Z

If the entry is incorrect, the LED (68) of the O key (69) flashes in red. Enter the
parameter number again to repeat the setting.

Z

The  parameter  and  sub  index  are  displayed  alternately  with  the  current  reading
(0256-2<->0000-5).

The travel parameter is now set.

Repeat the procedure to enter further parameters as soon as the LED (68) of the O
key (69) flashes.

Z

Travel is disabled while the parameters are being entered.

Checking the setting in programming mode

Procedure

• Select the travel program to be worked on after entering the parameter value, and

confirm with the Set key (67).

The truck is now in travel mode and can be checked.

125

04.19 en-GB

Содержание EJE 220









































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды