manualshive.com logo in svg

Jungheinrich EJE 220, Руководство по эксплуатации

Поделиться
Скачать
Jungheinrich EJE 220 Скачать руководство пользователя страница 129

7.6

Setting the Battery Parameters with CanCode

WARNING!

Altering parameters can cause accidents

u

Altering the settings can cause accidents.

u

This  requires  greater  attention  on  the  part  of  the
operator

The  following  example  shows  the  parameter  setting
for  the  battery  type  (parameter  1377)  to  "dry  -
maintenance-free".

Requirements

– CanCode and CanDis are available.

Procedure

• Press the O key (69).
• Enter the master code.
• Enter  the  four-digit  parameter  number  "1377"  and

confirm with the Set key.

• Enter sub index "2" and confirm with the Set key.

The  parameter  with  subindex  are  displayed
alternately with the current reading. E.g. (1377-2<-
>0000-1--corresponds  to  battery  type  „high-
performance (wet)”.

• Enter parameter "2" according to the parameter list

and confirm with the Set key.

The  LED  of  the  O  key  switches  briefly  to
continuous  light  and  starts  flashing  again  after
approx. 2 seconds.

If the entry is incorrect, the LED of the O key turns
red.  Enter  the  parameter  number  again  to  repeat
the setting.

The  parameter  and  subindex  are  displayed
alternately  with  the  current  reading  (1377-2<-
>0000-2).

The "dry maintenance-free" battery type is set.

Z

Travel  is  disabled  while  the  parameters  are  being
entered.
Storing the parameter

Requirements

– The parameter is now entered.

Procedure

• Run "SaveParameters" by pressing 1-2-3-Set.
• Press the O key.

67

64

65

66

69

68

129

04.19 en-GB

Содержание EJE 220









































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды