Jungheinrich EJE 220 Скачать руководство пользователя страница 159

Страница: 159 / 232

4.4

Front cover disassembly

Requirements

– Prepare the truck for maintenance

and repairs, see page 154.

Tools and Material Required

– Allen key size 8

Procedure

• Remove the screws (95) with the

Allen key.

• Lift and remove the front panel

(15).

• Place the front panel (15) safely to

one side.

The front cover has been removed.

Front panel assembly

Tools and Material Required

– Allen key size 8

Procedure

• Insert the front panel (15) carefully and secure it.
• Attach the front cover (15) to the truck with the screws (95). Tighten the

screws (95) with the Allen key.

The front panel is now assembled.

159

04.19 en-GB

Содержание EJE 220









































































































































































































































Результаты поиска

Содержание EJE 220

Отзывы:

Бренды по названию

Популярные бренды

Jungheinrich EJE 220, Руководство по эксплуатации

Результаты поиска

Содержание EJE 220

Отзывы:

Бренды по названию

Популярные бренды