Judo JRSF Series Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 55

background image

Installation and operating instructions: JUDO JRSF automatic backwashing protection filter JRSF-ATP DN 125 - 200 (time and differential pressure controlled)

All rights reserved.

JUDO Wasseraufbereitung GmbH

© JUDO Wasseraufbereitung GmbH

Postfach 380



D-71351 Winnenden

Translation into foreign languages and reproduction, even in excerpt form, is only permitted with special
approval.

Tel. +49 (0)7195-692-0



Fax +49 (0)7195-692-188

Revision level: 24.05.2017

E-mail: [email protected]



judo.eu

44

Fault

Cause

Remedy

Backwashing process
does not start correctly

Power failure

Check mains connection cable and fuses,
replace as necessary

Differential pressure gauge set
incorrectly or defective

Check differential pressure gauge, if
necessary set or replace

Incorrect programming

Check the programming, correct as
necessary

“Hall fault” with interruption
of the backwashing

Connecting cable interrupted

Check linear drive connecting cable

Malfunction of the control unit
or Hall effect sensor defective

Check control unit, replace linear drive, if
necessary request JUDO customer service

“Fault
diff.pressure/external”

No reduction in the differential

pressure

Remove permanent filter inserts and clean,
end request at “PD” input

Backwashing pressure too low

Ensure min. required flow pressure
(E.g. throttle filter outlet)

External requirement for
backwashing exists for too long

End requirement at “EX” input

Solenoid valve not
energised

Incorrect programming

Check the programming, correct as
necessary

Solenoid valve defective

Replace solenoid valve

Tab. 12: Electrical faults

If a fault cannot be rectified based on the information in Table 11 or 12, contact your JUDO customer service
representative or an authorised specialist company.

JUDO Wasseraufbereitung GmbH

JUDO Wasseraufbereitung AG

Winnenden Works

Austrian subsidiary

Address: Hohreuschstraße 39-41 Zur Schleuse 5

Industriestrasse 15

D-71364 Winnenden

A-2000 Stockerau

CH-4410 Liestal

Phone:

+49 (0)7195-692-0

+43 (0)2266-640-78

+41 (0)61-90640-50

Fax:

+49 (0)7195-692-188

+43 (0)2266-640-79

+41 (0)61-90640-59

Email:

[email protected]

[email protected]

[email protected]

Internet:

www.judo.eu

www.judo-online.at

www.judo-online.ch

Installation company:

«
...
42
43
44
45
46
...
»

Содержание JRSF Series
























































Отзывы:

Нет отзывов

Похожие инструкции для JRSF Series

Бренд: Zodiac Страницы: 12

Бренд: Oasis Страницы: 20

Бренд: 3M Страницы: 8

Бренд: Aqua FX Страницы: 7

Spectra Watermakers Catalina 340R

Бренд: Katadyn Страницы: 73

Бренд: Jandy Страницы: 48

Бренд: Halo Страницы: 24

Thunder CQE-CT-00142

Бренд: Crystal Quest Страницы: 4

clearspring mini 110572

Бренд: ThePondguy Страницы: 8

Бренд: Ryobi Страницы: 2

Chemical-Free Water Conditioner NONE

Бренд: P3 International Страницы: 1

Бренд: Task Force Tips Страницы: 12

Бренд: IDEAL Страницы: 68

Бренд: Galley-Mate Страницы: 10

Бренд: 3M Страницы: 12

Бренд: Aqualife Страницы: 17

Бренд: Dahlert Страницы: 12

Бренд: Tyco Fire Product Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды