JS Automation YPV-040 Скачать руководство пользователя страница 11

Страница: 11 / 70

Extra Notices:

Do not install the servo drive in locations likely to be affected by oil and dust. If unavoidable,

please install the Servo drive in the airtight control cabinet and consider using ventilation filter.

Also use a protective cover over the Servomotor.

When installing multiple servo drives in one airtight control cabinet, allow at least 50mm between,

above and below each servo drive and leave 120mm for maintenance space. In addition, to ensure

the reliability and improve the product life, leave certain distance between the servo drive and the

cabinet ceiling so the temperature around the servo drive does not exceed 55 C which might lead

to poor ventilation.

A frequent use of the regenerative resistor may lead to a temperature higher than 100 C. Do not

put inflammables or heating deformable objects around. The wirings must also be kept away from

the resistor or severe damage will occur.

When installing near a source of vibration, install a vibration isolator to protect the Servo drive

from vibration.

Содержание YPV-040







































































Результаты поиска

Содержание YPV-040

Отзывы:

Похожие инструкции для YPV-040

Бренды по названию

Популярные бренды

JS Automation YPV-040, Руководство пользователя

Результаты поиска

Содержание YPV-040

Отзывы:

Похожие инструкции для YPV-040

Бренды по названию

Популярные бренды