JR X9303 Скачать руководство пользователя страница 32

Страница: 32 / 48

GOVERNOR- GOVERNOR FUNCTION

H-32

Note

: The GOVERNOR function is only listed/shown

in the Function Mode when first activated/selected in

the Device Select function in System Mode.

The X9303 2.4’s Governor function is designed to be used

with most currently available Governors on the Market.

The Governor function allows the Governor rpm values

to be set for each of the Active Flight modes, and will

automatically change the Governor rpm values as set

when the Flight Mode switch is moved through each of

the active flight modes.

The value range in the Governor function is +/- 0%–

125%, and its values follow the Travel Adjust values

exactly. In other words, a desired Travel Adjust value of

+55% would also be +55% in the Governor function.

The Governor program, when activated in System Mode,

functions through the GEAR channel (Channel 5) of

the X9303 2.4. When connecting a Governor to the

receiver, the rpm signal lead from the Governor would be

connected to the Gear (CH5) channel for proper operation.

Accessing the Governor Function

1. Place the transmitter switch in the ON position.
2. Press the

LIST

key to enter the

Function mode

3. Move the

Selector

and highlight the

GOVERNOR

function. Press the

Selector

to access.

4. Highlight the desired value to be adjusted with the

Selector,

and then press to access the value. Roll the

Selector

to adjust the value as needed.

5. To exit the Governor function, move the

Selector

highlight

LIST

, and press.

Note

: Flight Modes ST-3 and ST-4 will only be

shown if activated previously in

System Mode.

For Governors like the Model Avionics “Throttle Jockey,”

you would leave the Travel Adjust values for the Gear

channel at +/-100%, and you would then set your

Governor rpm values from the rpm calculator in the

Governor function.

For other brand Governors, you would also leave

the Travel Adjust values for the Gear Channel (CH5)

at +/-100%. You could then increase the values in the

Governor function above +/-100% up to +/-125% to

increase the rpm remotely from the preset rpm selected at

the Governor.

Note

: To turn off the Governor Function for engine

tuning, etc. it will be necessary to return the value for

the desired flight mode to zero. Remember the value

so it can be re-entered after tuning.

[GOVERNOR]

NORM: + 55%

ST-1: + 80%

ST-2: + 85%

ST-3:

ST-4:

HOLD:

◊

Содержание X9303

















































Результаты поиска

Содержание X9303

Отзывы:

Бренды по названию

Популярные бренды

JR X9303, Руководство пользователя

Результаты поиска

Содержание X9303

Отзывы:

Бренды по названию

Популярные бренды