JR ProPo PCM9XII, Инструкция по эксплуатации

Страница: 58 / 88

MacGregor Industries
54 AERO
Slave Channel Identification.
THRO Throttle channel. FLAP Flap channel.
AILE Aileron channel. AUX2 Auxiliary 2 channel.
ELEV Elevator channel. AUX3 Auxiliary 3 channel.
RUDD Rudder channel. AUX4 Auxiliary 4 channel.
GEAR Gear channel. FPRN Flaperon function (both Ailerons as Flaps).
To activate the mix, select and click on INH or press the CLR key on the left of the screen. The default is for THRO
(Throttle) to be mixed to THRO (Throttle).
To clear (inhibit) the mix, highlight either the "Master or Slave select" menu choice and press the CLR key.
To select a Master channel, highlight the left hand THRO (or previously selected Master channel) by rotating the Scroll
Bar and click on it to bring up the sub menu. A browse box of the available Master channels appears with a heading of
Mast to indicate that the Master channel is being selected. Rotate the Scroll Bar to select the required channel and click on it
to exit the sub menu. To exit without making changes, select and click on the CANCEL menu choice. Please note that
when SNPT (The snap roll bias switch) is selected as a Master input, the Slave will toggle between
±
100% with each
activation of the switch.
To select a Slave channel, highlight the right hand THRO (or previously selected Slave channel) by rotating the Scroll Bar
and click on it to bring up the sub menu. A browse box of the available channels appears with a heading of Slav to indicate
that the Slave channel is being selected. Rotate the Scroll Bar to select the required channel and click on it to exit the sub
menu. To exit without making changes, select and click on the CANCEL menu choice. Please note that if FPRN
(Flaperon, Ailerons as Flaps) is selected as a Slave, the mix causes both Aileron servos move up and down in the same
direction (like Flaps). If Aileron is selected as a Slave, the mix causes the Aileron servos to move in opposite directions
(like Ailerons).
To set a mix value, highlight the required mix position (Pos0 or Pos1) by rotating the Scroll Bar and click on it to bring up
the sub menu. The figures are surrounded by a box to indicate that they are selected. Move the Master stick/switch/lever
to select either the top or the bottom figure and rotate the Scroll Bar to alter the setting. Note that only the mix figure for
the selected side of neutral is changed. To return the figures to the default of 0, press the clear (CLR) key at the left hand
side of the screen. When the required setting is achieved, click the Scroll Bar to exit the sub menu. Note that when the mix
is permanently on, any entries for Pos1 (position 1) are ignored.
To set an offset value, highlight "Offset" by rotating the Scroll Bar and click on it to bring up the sub menu. The figure is
surrounded by a box to indicate that it is selected. Rotate the Scroll Bar to alter the setting. To return the figures to the
default of 0, press the clear (CLR) key at the left hand side of the screen. When the required setting is achieved, click the
Scroll Bar to exit the sub menu.
To select an activation switch, highlight the required switch by rotating the Scroll Bar and click on it to toggle between
position "0" and position "1". The black indicator square moves between the top of the box (POS1) and the bottom of the
box (POS0) to indicate the current selection. The selection toggles between POS0 and POS1 with each click. To return the
sub menu selection to the default of position 0 (POS0), press the clear (CLR) key at the left hand side of the screen. When
the required setting is achieved, click the Scroll Bar to exit the sub menu. Please note that the Flight Mode switch
selection will only appear if Flight Modes have been activated in System Mode - DeviceSEL.