Jonsered GC2126C Скачать руководство пользователя страница 17

Страница: 17 / 27

WORKING TECHNIQUES

General working instructions

IMPORTANT!

This section describes the basic safety pre-

cautions for working with trimmers. If you

encounter a situation where you are uncer-

tain how to proceed you should ask an ex-

pert. Contact your servicing dealer.

Avoid all usage which you consider to be

beyond your capability.

You must understand the difference between

forestry clearing, grass clearing and grass

trimming before use.

Basic safety rules

1. Look around you:

To ensure that people, animals or other

things cannot affect your control of the

machine.

To ensure that people, animals, etc.,

do not come into contact with the cut-

ting attachment or loose objects that

are thrown out by the cutting attach-

ment.

CAUTION!

Do not use the machine

unless you are able to call for help in

the event of an accident.

2. Do not use the machine in bad weather,

such as dense fog, heavy rain, strong

wind, intense cold, etc. Working in bad

weather is tiring and often brings added

risks, such as icy ground, unpredictable

felling direction, etc.

3. Make sure you can move and stand safely.

Check the area around you for possible ob-

stacles (roots, rocks, branches, ditches, etc.)

in case you have to move suddenly. Take

great care when working on sloping ground.

4. Switch off the engine before moving to

another area. Fit the transport guard before

carrying or transporting the equipment any

distance.

5. Never put the machine down with the engine

running or while the cutting attachment is

rotating.

WARNING:

Sometimes branches

or grass get caught between the

guard and cutting attachment.

Always stop the engine before

cleaning.

WARNING:

Neither the operator

of the machine nor anyone else

may attempt to remove the cut ma-

terial while the engine is running or

the cutting equipment is rotating,

as this can result in serious injury.

Stop the engine and cutting equip-

ment before you remove material

that has wound around the blade

shaft as otherwise there is a risk of

injury. The bevel gear can get hot

during use and may remain so for a

while afterwards. You could get

burned if you touch it.

WARNING:

Watch out for

thrown objects. Always wear ap-

proved eye protection. Never lean

over the cutting attachment guard.

Stones, rubbish, etc. can be thrown

up into the eyes causing blindness

or serious injury. Keep unautho-

rised persons at a distance. Chil-

dren, animals, onlookers and help-

ers should be kept outside the

safety zone of 15 m. Stop the ma-

chine immediately if anyone ap-

proaches. Never swing the ma-

chine around without first checking

behind you to make sure noone is

within the safety zone.

The ABC of clearing

Always use the correct equipment.

Make sure the equipment is well adjusted.

Follow the safety precautions.

Organise your work carefully.

Always use full throttle when starting to cut

with the blade.

Always use sharp blades.

Avoid stones.

Basic working techniques

Always slow the engine to idle speed after

each working operation. Long periods at

full throttle without any load on the engine

can lead to serious engine damage.

Содержание GC2126C




























Результаты поиска

Содержание GC2126C

Отзывы:

Похожие инструкции для GC2126C

Бренды по названию

Популярные бренды

Jonsered GC2126C, Руководство оператора

Результаты поиска

Содержание GC2126C

Отзывы:

Похожие инструкции для GC2126C

Бренды по названию

Популярные бренды