Jonsered GC2126C Скачать руководство пользователя страница 15

Страница: 15 / 27

STARTING AND STOPPING

Check before starting

Check the blade to ensure that no cracks

have formed at the bottom of the teeth or

by the centre hole. The most common rea-

son why cracks are formed is that sharp

corners have been formed at the bottom of

the teeth while sharpening or that the blade

has been used with dull teeth. Discard a

blade if cracks are found.

Check that the support flange is not

cracked due to fatigue or due to being

tightened too much. Discard the support

flange if it is cracked.

Ensure the locking nut has not lost its cap-

tive force. The nut lock should have a

locking force of at least 1.5 Nm. The tight-

ening torque of the locking nut should be

35--50 Nm.

Check that the trimmer head and trimmer

guard are not damaged or cracked.

Replace the trimmer head or trimmer

guard if they have been exposed to

impact or are cracked.

Never use the machine without a guard

nor with a defective guard.

All covers must be correctly fitted and un-

damaged before you start the machine.

Cold engine

Primer bulb:

Press the primer bulb 10

times until fuel begins to fill the bulb. The

primer bulb need not be completely filled.

Choke:

Move the blue engine choke lever

over to the closed position.

Starting

Hold the body of the machine on the

ground using your left hand (

CAUTION!

Not with your foot!).

Firmly grip the starter rope handle with

your right hand.

DO NOT squeeze

throttle trigger.

Slowly pull out the cord

until you feel some resistance (the starter

pawls grip); then quickly and powerfully

pull the cord.

Never wrap the starter cord around

your hand.

Repeat pulling the cord until the engine

attempts to start. Squeeze throttle trigger

to release the choke.

Continue to hold

throttle trigger

and pull starter rope until

engine runs.

WARNING:

The complete clutch,

clutch cover, and shaft must be

fitted before the machine is started,

otherwise parts could come loose

and cause personal injury.

Always move the machine away

from the refueling area before

starting. Place the machine on a

flat surface. Ensure the cutting at-

tachment cannot come into contact

with any object.

Make sure no unauthorized

persons are in the working area,

otherwise there is a risk of serious

personal injury. The safety

distance is 15 meters.

Starting and stopping

Содержание GC2126C




























Результаты поиска

Содержание GC2126C

Отзывы:

Похожие инструкции для GC2126C

Бренды по названию

Популярные бренды

Jonsered GC2126C, Руководство оператора

Результаты поиска

Содержание GC2126C

Отзывы:

Похожие инструкции для GC2126C

Бренды по названию

Популярные бренды