Jonsered GC2126C Скачать руководство пользователя страница 8

Страница: 8 / 27

GENERAL SAFETY PRECAUTIONS

WARNING:

Bear in mind that:

Engine exhaust fumes contain car-

bon monoxide, which can cause

carbon monoxide poisoning. For

this reason you should not start or

run the machine indoors, or any-

where that is poorly ventilated.

The exhaust fumes from the engine

are hot and may contain sparks

which can start a fire. Never start

the machine indoors or near com-

bustible material!

Locking nut

A locking nut is used to secure some types

of cutting attachment.

When fitting, tighten the nut in the opposite

direction to the direction of rotation of the

cutting attachment. To remove it, undo the

nut in the same direction as the cutting at-

tachment rotates. (

CAUTION!

The nut has

a left--hand thread.) Tighten the nut using

the socket spanner.

The nylon lining inside the locking nut must

not be so worn that you can turn it by

hand. The lining should offer a resistance

of at least 1.5 Nm. The nut should be re-

placed after it has been put on approx. 10

times.

Cutting equipment

This section describes how to choose and

maintain your cutting equipment in order to:

Reduce the risk of blade thrust.

Obtain maximum cutting performance.

Extend the life of cutting equipment.

IMPORTANT!

Only use cutting attachments with the guards

we recommend! See the section on

“Technical data”.

Refer to the instructions for the cutting attach-

ment to check the correct way to load the

trimmer line and the correct line diameter.

Keep the teeth of the blade correctly sharp-

ened! Follow our recommendations. Also re-

fer to the instructions on the blade packaging.

Maintain the correct blade setting! Follow our

instructions and use the recommended file

gauge.

WARNING:

Always stop the en-

gine before doing any work on the

cutting attachment. This continues

to rotate even after the throttle has

been released. Ensure that the

cutting attachment has stopped

completely and disconnect the

lead from the spark plug before

you start to work on it.

WARNING:

Using an incorrect

cutting attachment or an incorrect-

ly sharpened blade increases the

risk of kickback.

Cutting equipment

Grass blades and grass cutters are in-

tended for cutting coarse grass.

A trimmer head is intended for trimming

grass.

General rules

Only use cutting attachments with the

guards we recommend! See the section on

Technical data.

Keep the teeth of the blade correctly sharp-

ened! Follow our instructions and use the

recommended file gauge. An incorrectly

sharpened or damaged blade increases the

risk of accidents.

Содержание GC2126C




























Результаты поиска

Содержание GC2126C

Отзывы:

Похожие инструкции для GC2126C

Бренды по названию

Популярные бренды

Jonsered GC2126C, Руководство оператора

Результаты поиска

Содержание GC2126C

Отзывы:

Похожие инструкции для GC2126C

Бренды по названию

Популярные бренды