Jonsered GC2126C Скачать руководство пользователя страница 11

Страница: 11 / 27

ASSEMBLY

Adjusting the harness

Insert your right arm and head through

the harness and allow it to rest on your

left shoulder. Make sure the harness

hook is to the right side of your waist.

NOTE:

A one-half twist is built in the har-

ness to allow the harness to rest flat on the

shoulder.

Adjust the harness, allowing the hook to

be about 6 inches (15 cm) below the

waist.

Fasten the harness to the harness clamp

on the shaft and lift the unit to the operat-

ing position.

Put on the harness. Now make a final

adjustment so that the unit is in a com-

fortable working position when it hangs

from the harness.

NOTE:

It may be necessary to relocate

the harness clamp on the shaft for proper

balancing of unit.

Insert two screws into the screw holes.

Secure harness clamp by tightening

screws with a hex wrench.

Correct height

Adjust the harness so that the cutting at-

tachment is parallel to the ground.

Fitting the harness clamp

Place the upper harness clamp over the

shaft and position the lower harness

clamp under the shaft. Align the upper

and lower clamp screw holes. Clamp

must be fitted above the arrow on the

shaft (see illustration).

Correct balance

Let the cutting attachment rest lightly on

the ground. If you use a grass blade, it

should balance about 4 inches (10 cm)

above the ground to prevent contact with

stones and the like. Adjust the position of

the harness clamp to balance the unit cor-

rectly.

itting blades and trimmer

heads

When fitting the cutting attachment it is

extremely important that the raised section

on the drive disc/support flange engages

correctly in the centre hole of the cutting

attachment. If the cutting attachment is

fitted incorrectly it can result in serious and/

or fatal personal injury.

WARNING:

Never use a cutting

attachment without an approved

guard. See the section on Techni-

cal data. If an incorrect or faulty

guard is fitted this can cause seri-

ous personal injury.

Содержание GC2126C




























Результаты поиска

Содержание GC2126C

Отзывы:

Похожие инструкции для GC2126C

Бренды по названию

Популярные бренды

Jonsered GC2126C, Руководство оператора

Результаты поиска

Содержание GC2126C

Отзывы:

Похожие инструкции для GC2126C

Бренды по названию

Популярные бренды