Jonsered GC2126C Скачать руководство пользователя страница 22

Страница: 22 / 27

MAINTENANCE

Sharpening grass cutters and

grass blades

See the cutting attachment packaging for

correct sharpening instructions.

Sharpen blades and cutters using a

single--cut flat file.

Sharpen all edges equally to maintain the

balance of the blade.

WARNING:

Always discard a

blade that is bent, twisted, cracked,

broken or damaged in any other

way. Never attempt to straighten a

twisted blade so that it can be re-

used. Only use original blades of the

specified type.

WARNING:

Always stop the en-

gine before doing any work on the

cutting attachment. This continues

to rotate even after the throttle has

been released. Ensure that the cut-

ting attachment has stopped com-

pletely and disconnect the HT lead

from the spark plug before you start

to work on it.

Bevel gear

The bevel gear is filled with the right quan-

tity of grease at the factory. However, be-

fore using the machine you should check

that the bevel gear is filled three--quarters

full with grease. Use JONSERED special

grease.

The grease in the bevel gear does not nor-

mally need to be changed except if repairs

are carried out.

Содержание GC2126C




























Результаты поиска

Содержание GC2126C

Отзывы:

Похожие инструкции для GC2126C

Бренды по названию

Популярные бренды

Jonsered GC2126C, Руководство оператора

Результаты поиска

Содержание GC2126C

Отзывы:

Похожие инструкции для GC2126C

Бренды по названию

Популярные бренды