Jonsered FRM13 Automatic Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 36

background image

10

– English

PRESENTATION

!

Fuelling

The engine should be run on 85 octane (or higher)
unleaded petrol/gasoline (no added oil). Environ-
mentally adapted alkylate fuel, such as Aspen, is
also recommended.

Seat

The seat has a jointed attachment on the front
edge and can be tipped forward.

The seat can also be adjusted lengthways.

Release the knobs under the seat and adjust it
forwards or backwards to the required position.

Lock the setting with the knobs.

Lever for adjustment of cutting height

With this lever the cutting height can be adjusted to
9 different positions.

The cutting height of a Mulcher unit is 45-95 mm.

WARNING!
Petrol/gasoline is highly inflammable.
Observe care and fill up with fuel
outdoors (see safety instructions).

«
...
10
11
12
13
14
...
»

Содержание FRM13 Automatic





































Отзывы:

Нет отзывов

Похожие инструкции для FRM13 Automatic

Бренд: Vari Страницы: 56

Бренд: Yard Machines Страницы: 24

MT, MTL, MTEFI, MTLEFI

Бренд: Walker Страницы: 256

Бренд: Walker Страницы: 96

Бренд: Yard force Страницы: 25

Бренд: Barbieri Страницы: 2

Бренд: Jacobsen Страницы: 50

Бренд: Draper Страницы: 8

Бренд: Draper Страницы: 16

Blizzard 17,5 H

Бренд: EMAK Страницы: 338

Бренд: Simplicity Страницы: 11

Бренд: Raider Страницы: 62

Бренд: Honda Страницы: 24

Reelmaster 7000

Бренд: Toro Страницы: 315

Бренд: Exmark Страницы: 5

GE-PM 51S-F B&S

Бренд: EINHELL Страницы: 144

Бренд: EINHELL Страницы: 84

Бренд: MTD Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды