Jonsered FRM13 Automatic Скачать руководство пользователя | Manualshive

Страница: 31 / 36

background image

English –

29

MAINTENANCE

Checking and adjustment of the
throttle wire

If the engine does not respond as it should do when
the throttle lever is moved or if the top speed is not
reached, the throttle wire may need adjusting.

1. Release the clamping screw (see arrow) and

push the throttle control to full throttle position.

Replacement of the fuel filter

Replace the pipe fitted fuel filter every 100 running
hours (once per season) or more frequently if it is
clogged.

Replace the filter as follows:

1. Dismantle the engine hood as described on

page 17.

2. Move the hose clips away from the filter. Use a

pair of flat pliers.

3. Pull off the filter from the hose ends.

4. Press in the new filter on the hose ends. If

necessary soap solution can be applied on the
filter ends to simplify fitting.

5. Push the hose clips back on the filter.

2. Pull the throttle wire’s outer casing to the far

right and tighten the clamping screw.

«
...
29
30
31
32
33
...
»

Содержание FRM13 Automatic





































Отзывы:

Нет отзывов

Похожие инструкции для FRM13 Automatic

Бренд: ECLOZ Страницы: 60

Бренд: Snapper Страницы: 40

Бренд: Hayter Страницы: 56

Бренд: Cub Cadet Страницы: 56

Бренд: Texas Страницы: 60

Бренд: Yard force Страницы: 23

Бренд: Weed Eater Страницы: 4

Бренд: Bad Boy Страницы: 48

Бренд: Rally Страницы: 19

Бренд: Kees Страницы: 23

Бренд: Poulan Pro Страницы: 48

Бренд: Alamo Industrial Страницы: 186

Бренд: Toro Страницы: 44

Бренд: Ransomes Страницы: 100

Бренд: Yard-Man Страницы: 12

Бренд: MTD Страницы: 16

Бренд: Western Auto Страницы: 40

Бренд: Worx Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды