Jonsered FRM13 Automatic Скачать руководство пользователя

Страница: 22 / 36

– English

MAINTENANCE

Check the transmission’s oil level

1. Check the transmission’s oil level by removing

the transmission cover. Release the two screws
(one of each side) and lift off the transmission
cover.

WARNING!
Procedures on contact with acid

External: Rinse well with plenty of water.

Internal: Drink large quantities of water or

milk. Contact a doctor as soon as
possible.

Eyes:

Rinse well with plenty of water.
Contact a doctor as soon as possible.

Batteries emit explosive gas. Sparks, flames
and cigarettes must absolutely not be
brought into the vicinity of the battery.

Check the level of the battery acid

Check that the level of the battery acid lies be-
tween the markings. Top up the cells with

only

distilled water.

FULL

2. Unscrew the oil cap and check that the oil level

lies between the markings on the dip stick. Top
up if necessary with engine oil SAE 10W/30
(class CD-SF) in the same hole as for the dip
stick.

Check the safety system

The machine is equipped with a safety system which prevents starting the cutting unit or driving the machine
unless someone is sitting in the seat.

Check daily the safety system functions.

This check is carried out by applying the parking brake and raising the cutting unit into the transport position.
Start the engine and get off the machine. When the cutting unit is lowered into the cutting position the engine
should stop.

Содержание FRM13 Automatic





































Результаты поиска

Содержание FRM13 Automatic

Отзывы:

Похожие инструкции для FRM13 Automatic

Бренды по названию

Популярные бренды

Jonsered FRM13 Automatic, Руководство оператора

Результаты поиска

Содержание FRM13 Automatic

Отзывы:

Похожие инструкции для FRM13 Automatic

Бренды по названию

Популярные бренды