Jonsered FRM13 Automatic Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 36

background image

English –

27

Lubrication

The following two lubrication points should be
regularly lubricated with high quality graphite
grease.

With daily use lubrication should be conducted
twice a week.

General lubrication

All joints and bearings are lubricated on manufac-
ture with molybdenum sulphide grease. Re-grease
with same type of grease. Lubricate the steering
and control wires with engine oil.

The machine should be lubricated regularly, and
twice a week when used daily.

Checking the tyre pressure

The tyre pressure should be 60 kPa (0.6 kp/cm

2

) all

round.

To improve driving the pressure on the rear tyres
can be reduced to 40 kPa (0.4 kp/cm2).

The maximum tyre pressure is 100 kPa (1.0 kp/cm

2

).

IMPORTANT INFORMATION

Different tyre pressures on the front tyres
will result in the blades cutting the grass
at different heights.

MAINTENANCE

«
...
27
28
29
30
31
...
»

Содержание FRM13 Automatic





































Отзывы:

Нет отзывов

Похожие инструкции для FRM13 Automatic

Бренд: Baroness Страницы: 85

Бренд: Poulan Pro Страницы: 48

Бренд: Toro Страницы: 28

Derby Stallion ZT2561

Бренд: Simplicity Страницы: 39

RANSOMES 933304J

Бренд: Textron Страницы: 28

Бренд: Cub Cadet Страницы: 2

Бренд: RHINO Страницы: 98

Бренд: Montgomery Ward Страницы: 16

Бренд: Land Pride Страницы: 2

Бренд: Land Pride Страницы: 2

Cruisematic 141-846H190

Бренд: White Outdoor Страницы: 32

Scamper HG GDB10025

Бренд: Great Dane Страницы: 88

ZT 915100 - 1732

Бренд: Gravely Страницы: 32

Бренд: Craftsman Страницы: 20

Бренд: Craftsman Страницы: 44

Бренд: Craftsman Страницы: 44

Бренд: Craftsman Страницы: 44

Бренд: Craftsman Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды