Jonsered FRM13 Automatic Скачать руководство пользователя

Страница: 32 / 36

– English

Problem

Procedure

Engine will not start.

•

Fuel tank empty.

•

Plug defective.

•

Plug connection defective.

•

Dirt in carburettor or fuel pipe.

Starter does not pull round engine.

•

Battery flat.

•

Bad contact between cable and battery terminal.

•

Lift lever for cutting unit in wrong position.

•

Main fuse blown. The fuse is placed in front of the
battery, under the battery cover.

•

Ignition lock faulty.

•

Gear shift/hydrostat pedal not in neutral.

Engine does not run smoothly.

•

Wrong gear, too high.

•

Carburettor incorrectly set.

•

Air filter clogged.

•

Fuel tank vent blocked.

•

Ignition setting defective.

•

Dirt in fuel pipe.

Engine seems to have no power.

•

Air filter clogged.

•

Plug defective.

•

Dirt in carburettor or fuel pipe.

•

Carburettor incorrectly set.

Engine overheats.

•

Engine overloaded.

•

Air intake or cooling flanges blocked.

•

Fan damaged.

•

Too little or no oil in engine.

•

Ignition defective.

•

Plug defective.

Battery does not charge.

•

One or more cells faulty

•

Bad contact between battery terminals and cables.

Machine vibrates.

•

Blades are loose.

•

Engine is loose.

•

Imbalance on one or more blades, resulting from
damage or inferior balancing after sharpening.

Uneven mowing.

•

Blades blunt.

•

Cutting unit skew.

•

Long or wet grass.

•

Grass blockage under hood.

•

Different tyre pressures on right and left sides.

•

Over-speeding

•

Drive belts slipping.

TROUBLE SHOOTING SCHEDULE

Содержание FRM13 Automatic





































Результаты поиска

Содержание FRM13 Automatic

Отзывы:

Похожие инструкции для FRM13 Automatic

Бренды по названию

Популярные бренды

Jonsered FRM13 Automatic, Руководство оператора

Результаты поиска

Содержание FRM13 Automatic

Отзывы:

Похожие инструкции для FRM13 Automatic

Бренды по названию

Популярные бренды